QOMO 5000 UHD 4K Desktop Document Camera User Manual

QOMO 5000 UHD 4K Desktop Document Camera

Precautions

WARNING

• Risk of electric shock
• Dangerous voltage inside

Please follow these precautions

• To prevent fire or shock hazards, do not expose the unit to rain or moisture.
• To prevent electrical shock, do not open the cabinet. Refer to qualified personnel for service only.
• Do not use the unit continuously for more than 24 hours with camera autofocus on. It may cause damage to the camera lens.
• Be careful not to spill water or other liquids onto the unit, or allow combustible or metallic objects to get inside the cabinet.
• Unplug the visualizer from the wall outlet when it is not in use for an extended period.
• Clean the cabinet with a soft cloth lightly moistened with a mild detergent. Clean the lens carefully with an air spray or soft dry cloth to avoid scratching. When lamps flash or become dark, they should be replaced with new ones. Avoid interchanging arm lamps and bottom lamps frequently.

Parts Identification

1. Zoom in/Zoom out Knob
2. Camera Stand
3. Left Arm Lamp
4. Bottom Lamp
5. Remote Control Slot
6. Preview screen
7. Control Panel
8. Camera Case
9. Infrared Receive Area
10. Rear Connector
11. Right Arm Lamp
12. Work Stage
13. Side Connector
14. Built-in Microphone
15. SD Card Slot

Control Panel

Button operation instruction

Remote Control

Lamp

| Control the arm lamp and bottom lamp
Auto| autofocus

Setting

| Select the Visualizer input signal

Source

| Select the Visualizer input signal

Resolution

| Select resolution from 720P ， 1080P, and 4K

directly

**| Move the cursor Left, Right, Up, Down/Confirm
Menu| Invoke menu
Zoom in/ Zoom out| Increase and decrease magnification
---|---
Snap| Capture a still image
Record| Record a video clip
Far/Near| Focus near or far**

Freeze

| Freeze the image, press again to unfreeze

Playback

| Re-display stored imaged

and videos

Flip| V-Reverse the image

Rotate

| Imagerotationof 0°,90°,180°,270°

Basic Preparations

1. Place one hand firmly on the base of the visualizer, while carefully lifting the camera stand using the other hand.
2. Open the arm lights and rotate the camera head until they are properly positioned.

Making Connections

• Connect to the projector or monitor
  • Use the HDMI cable to connect the HDMI out port to the projector’s or monitor’s HDMI input port.
  • WARNING: You can also connect the VGA OUT Port to the matching port
• Connect to a desktop computer
  • Use the HDMI cable to connect the HDMI out port to the monitor’s HDMI input port.
  • Use the HDMI cable to connect the HDMI in 1 port to the computer’s HDMI out port.
  • Now You can switch sources to display the computer or camera screen.
• Connect power source
  • Connect the power cord to the 12V IN connector.

WARNING: Before making any connections, turn off all the power. Please ensure that the visualizer along with all other equipment to be connected are turned off.

Mouse Operating Instructions

Move the mouse guide to the bottom middle of the screen, and the operation menu will pop up, and the menu functions are as follows:

Menu Operating Instructions

Function

| ****

| Resolution| 720P/1080P/2160P
Focus Mode| Auto Focus/ Manual Focus
Mask| Activate the Mask function
Split| Activate the Split function
Image Setting| ***| Photo Resolution| 38402160
Recording

Resolution

| 2160P@30FPS/1080P@30FPS/

720P@30FPS

System Setting

| ****

| Language| Support Chinese, English
System Time| /
Time Setting| User-defined
Display

Information

| Set to display the information on top of the

display or not.

File Manager

| Copy to external storage
Delete all
Format external storage
Connect USB Drive to PC
Connect SD card to PC
System Reset| Ensure/ Ignore
System Upgrade| Ensure/ Ignore
Lens FW upgrade| Ensure/ Ignore
PC Control| USB/DB9/PS2
User Profile| User 1/User 2/User 3

Effect Setting

| ****

| Mask Setting| 10%-80%

Mirror

| Normal
Left-right Mode
Up-down Mode

Effect

| Normal
Black-white Mode
Negative Mode
Flicker| Auto/50HZ/60HZ/Disable
Brightness, Sharpness, DNR,

Contrast,

Saturation

| ****

Use ( ) to adjust its setting.

Time-lapse Photo| ****| ON/OFF|
Interval| User-defined

Basic Operation

Device power on

• After connecting the power source, please wait for the source indicator to turn off, only the red light of the power button is on, and then press the power button.

Working on the stage

• Place your material on the platform.
• Select the enlargement required using the “zoom in/zoom out” knob.
• Adjust the focus of the “AUTO” button.

Working outside the stage

To show a 3-dimensional object using the visualizer, place the object on the working surface and adjust the “zoom in/out” and “AUTO” keys. If the object is too large for the stage or if you would like to show it from one of its sides, or a different angle, just place the object behind or in front of the unit and manually tilt the camera head (remove the close-up lens before titling the camera head).

Light

• The arm lights are powered on when the power is turned on. Each time you press the “LAMP” button, the lighting changes occur as demonstrated.

Adjusting image size

• To reduce or enlarge the image size displayed on the screen, rotate the Zoom in or Zoom out knob, or use the buttons on the control panel.

Quickly switch resolutions

• The factory default resolution is 1080P, switch the device between 2160p, 1080P, and 720P by clicking the “Resolution” button on the control panel.

WARNING: When using HDMI OUT to output video signal, when setting 2160p resolution, please make sure your monitor supports the display 4K screen. Otherwise, there will be no screen display, please press the “Resolution” button to switch to other resolutions.

Working with negatives

The visualizer is automatically set to display normal materials on the screen when the power is on. To display negatives, turn on the backlight by pressing the “LAMP” button, and then select (Effect Setting) in the menu-(Effect)-select “Negative” to display the film negatives. In the (Effect) list select “Normal” to display normal materials in the color mode.

Focusing

When the visualizer is turned on the focus automatically adjusts to the stage, press the “AUTO” button to autofocus. You can also manually adjust the focus with the near focus button or the far focus button.

Freezing image

• To show a still image on the screen, press the “Freeze” button. The frozen image cannot be adjusted (Zoom in/out, color adjustment, etc.).

Recording videos and Play

• Press the “Record” button to Record a video clip, and press it again to stop recording.
• Press the “Playback” button, The latest video will be displayed, Use the “up/down/Left/Right” buttons to select the file to be displayed, then press the “OK” button to play the video.

WARNING: Recorded videos are automatically saved every 20 minutes.

Camera / HDMI / VGA inputs

Press the “Source” button to switch between VGA, HDMI, and Camera signals. Each time the “Source” button is pressed, it provides seamless transitions among different sources such as VGA, HDMI IN 1, HDMI IN 2, and Camera.

WARNING

• HDMI IN signals can only output from HDMI OUT.
• VGA IN signals can only output from VGA OUT

Image rotation

To rotate the image, press the “Rotate” button once, and the displayed image will be rotated 90,180,270 degrees clockwise. Continue to press the “Rotate” button to restore the image to its initial position.

Infrared remote control

The visualizer’s remote control can control the camera from different angles. On the left side of the visualizer stage, there is a built-in remote control storage compartment where you can store the remote control when it is not in use. Please note that an infrared remote control can only be used up to a certain distance from the unit. Objects situated between the visualizer and the infrared remote control and a weak battery may interfere with the reception.

Installing visualizer software QCamera

The visualizer is a standard UVC camera – you can use it with a variety of software that supports a UVC camera connection. The visualizer is compatible with the third-party video conferencing software Zoom, Microsoft Teams, or Google Meet. However, to better experience the 4K UHD visualizer UVC function, we’d recommend using it with the QCamera and you can download this free from the QOMO website at the link below. https://www.qomo.com/qcamera

WARNING

• When the UVC function is in use, only Zoom in/out, Near, Far, lamp, brightness, Flip, and Autofocus functions are available on the panel and remote control
• To get the visualizer out of UVC mode, please manually disconnect the Camera from the software or exit the software , do not unplug the USB cable directly.

Controlling visualizer by computer

You can connect the DB9 (RS232) interface/PS2 interface/USB-type B interface on the visualizer to a computer to control the visualizer. For example, control via the DB9 interface:

• Connect the computer and the visualizer using the RS232 cable.
• select (System Setting) in the menu-(PC Control)-select “DB9” to control the visualizer.
• Use any serial port debugging software to control.

RS232 code list

Baud rate: 9600bps      Stop bit: 1-bit              Data bits: 8-bit

Odd-even check: none Communication encoding: Hex code

Function| Required Commands (Hex)
Power ON| 48 02 28 01 54
Power OFF| 48 02 18 02 54
Up| 48 02 28 1e 54
Down| 48 02 28 1f 54
Left| 48 02 28 20 54
Right| 48 02 28 21 54
OK| 48 02 28 22 54
Menu| 48 02 28 14 54
Bottom menu| 48 02 28 1d 54
Focus Far| 48 04 17 08 00 02 54
Focus Near| 48 04 17 08 00 03 54
Autofocus| 48 02 18 03 54
Zoom in| 48 04 17 07 00 04 54
Zoom out| 48 04 17 07 00 05 54
Arm lamp| 48 04 16 09 00 01 54
Bottom lamp| 48 04 16 09 00 02 54
All lamp Off| 48 04 16 09 00 00 54
Brightness Inc| 48 04 17 14 00 02 54
Brightness Dec| 48 04 17 14 00 03 54
Capture| 48 02 28 04 54
Replay| 48 02 28 07 54
Record| 48 02 28 05 54
720P| 48 04 16 12 00 ac 54
1080P| 48 04 16 12 00 10 54
2160P| 48 04 16 12 00 11 54
B & W| 48 04 16 10 00 01 54
Color| 48 04 16 10 00 00 54
Rotate| 48 04 17 0a 00 01 54
Mirror| 48 04 16 0b 00 01 54
Freeze| 48 04 16 0c 00 01 54
Switch the source to VGA| 48 04 16 13 00 01 54
Switch the source to HDMI2| 48 04 16 13 00 02 54
Switch the source to HDMI1| 48 04 16 13 00 03 54
Switch the source to Camera| 48 04 16 13 00 00 54

Folding The Unit

• Fold the right arm light down first onto the base, then the left arm down. Rotate the camera head clockwise until the camera head is parallel to the camera stand.
• Carefully fold the camera stand down to the front panel.

WARNING

• Do not lay the unit down flat.
• Do not try to stand it on its rear or sides.
• Do not try to pick up this unit by pulling the camera.

Problems And Solutions

The device does not turn on in the

normal condition.

| The power adapter is not connected correctly to the device or the power socket.| Make sure the power adapter r is connected correctly to the device and power socket.

After the device is connected, there is no image output.

| The device is not connected to the external equipment

correctly.

| Re-connect the device with the external equipment.
The external equipment is not selected correctly.| Select the correct external equipment.
The resolution of the external equipment is set incorrectly.| Reset the resolution of the external equipment.
The device is not switched to the correct source of signals.| Switch to the correct source of signals.
The computer transfer key (VGA) is activated.| Press the source of the signal (CAM).
HDMI is activated.| Press the source of the signal (CAM).
The image can not be moved around.| The image can not be moved around because the Freeze function of the device is activated.| Press again the Freeze function key on the control panel or the remote control to deactivate the function.

The remote control does not respond.

| The battery runs out.| Please replace the battery.
Objects are located between the remote control and the device and block the communication signals.| Please remove the objects that block the communication signals.
The distance between the remote control and the device is too far.| Please shorten the distance between the remote control and the device.

Specifications

Lens| 10X Optical Zoom

10X Digital Zoom

---|---
Shooting Area| A4

Video Resolution

| 720P: 1280 x 720

1080P: 1920 x 1080

2160P: 3840 x 2160

Image sensor Resolution| 8.3 Mega UHD
Frame Rate| 4K@30fps max
Camera Rotation| Vertically 330°
Image Rotation| 0°/90°/180°/270°

Input Connector

| HDMI 1.4b x 2 USB2.0 TYPE A x 1 RS232 DB9 x 1 RS232 PS2 x 1 VGA x 1

VGA AUDIO x 1

Line in x 1

RJ45 x 1

Output Connector

| Line out x 1 USB3.0 Type B x 1(UVC) HDMI 1.4b x 1(4K@30fps)

VGA x 1(1080P@60ps)

Microphone| Built-in
USB (UVC)| Yes
Video Output| Yes
On board Memory| Yes
Memory card| SD
LCD Preview| Yes
Focus| Auto/Manual selectable
White balance/exposure| Auto
Image split| Yes
Negative/positive conversion| Yes
Black/white and color selection| Yes
Image Freeze| Yes
Mirror| Yes
Remote Controller| Yes
Annotation| Yes
Mouse control| Yes
Ethernet| Yes
Lights| Arm Lamp: 1.5W LED lamps x 2
Bottom Lamp: 2.5W LED lamps
SD Card Slot| Yes (64GB max)
USB Memory Slot| Yes
Power Requirements| 12V 2A external AC adapter
---|---

Dimension (W x D x H)

| Folded: 510 x 410 x 120mm
Setup: 510 x 530 x 570mm
Packing: 600 x 200 x 480mm

Note: Specifications are subject to change without notice.

CONTACT

• Qomo.com
• 1-866-990-7666
• support@qomo.com

V1.0.2

References

• QOMO: Interactive Collaboration Technology | Powerfully Simple
• QCamera | Document Camera Software | QOMO
• QCamera | Document Camera Software | QOMO

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>