INTEZE CLIQ TWS EARPHONES User Manual

INTEZE CLIQ TWS EARPHONES

Product description

1. Microphone
2. Microphone
3. LED indication
4. Touch control area
5. Ear tip
6. LED indication
7. Charging case
8. USB-C charging interface

Pairing

After being taken out from the charging case, the earphones will be paired automatically together. Prior to the first use with every device, it is necessary to pair the earphones:

1. Remove both earphones from the case and wait for about 3 seconds before pairing mode is activated (both earbuds will flash blue).
2. Select “Intezze CLIQ” from the available BT devices on your phone and select connect (if necessary, confirm the intention to pair the earphones). After successful pairing you´ll hear a confirmation message “Connected”.

Powering ON / OFF

Power ON

Method 1: Take out the earphones from the charging case, the earphones will switch on automatically.
Method 2: In the off state, press and hold the touch area on both earphones for 3 seconds. The earphones will turn on and you can hear the prompt “power on”.

Power OFF

Method 1: Put the earphones into the charging box. They will shut down automatically, but not if the charging case runs out of battery.
Method 2: Turn off your phone’s Bluetooth and the earphone will automatically shut down in 3 minutes.
Method 3: Turn off your phone’s Bluetooth and hold the touch area on both earbuds for 4 seconds until you hear “Power off”.

Playback controls

In call controls

Voice assistant

Wake up / Cancel voice assistant: Touch the left or right earphone three times gently.

RESET function

If the earphones fail to connect / only one of the earphones is functional, you can reset them using the reset function:

1. Delete “Intezze CLIQ” from the list of paired devices on the phone (and deactivate the Bluetooth function on your phone).
2. Take both earbuds out of the case. Both earbuds’ LED will flash blue and you will hear the “Pairing” prompt.
3. Tap the touch area of one of the earbuds 5x quickly. Both earbuds’ LED will turn purple and then turn off. You will hear the “Power off” prompt.
4. Power on both earbuds by holding both touch areas for 3 seconds. You will hear the “Power on” prompt and both earbuds’ LED will flash red / blue alternately.
5. Place the earbuds next to each other so that you can see them. After 8–10 seconds both earbuds’ LED will flash blue.
6. Now you can repeat the pairing process with your phone.

Charging

The earbuds and the charging case need to be fully charged prior to first use!

Earphones: Put the earphones into the charging box, the charging case will automatically charge the earphone, and the earphone will display a red light when charging.

Charging case: Use the included USB-C cable to charge the case.

LED indication on the earbuds

LED indication on the case

or dim. Power indicator: Red light: 5-35%; orange light: 35 -70%; green light: 70%-100%
Charging earbuds| When you put the earbuds into the charging box, the LED will show the charging box battery status for about 8 seconds and then it will turn off
Charging error| Green light turns off after 8 seconds.
Charging error| Red light flashes quickly.

Voice prompts

Precautions

1. The case with earbuds needs to be fully charged prior to first-time use.
2. If the earbuds are left unused for over two weeks, please recharge the case with earbuds periodically.
3. Listen with the volume setting as low as possible. Listening at high volume for an extended period may result in permanent damage to your hearing.
4. Keep your earphones and accessories out of reach of children.
5. Children should use the earphones only under adult supervision.
6. Do not expose the earphones to water for a prolonged period. Do not use it when swimming, diving, or in the shower.
7. Using your earphones in a moist or dusty environment, or near a strong magnetic field, may result in an internal circuit failure.
8. Do not store your earphones in an environment where the temperature is below -15°C or above +50°C.
9. Do not charge the earphones and the charging case in an environment where the temperature is below 0°C.
10. Do not expose your earphones or charging case to direct sunlight (such as on a window sill or on a car dashboard) for an extended period of time.
11. To avoid damage to your earphones, do not disassemble or tamper with them, and do not insert any foreign matter into them.
12. Keep the earphone grille clean on both earphones in order to avoid sound degradation.

Warranty conditions

The warranty does not cover the following situations:

1. Damage caused by tampering with the device.
2. Filters clogged by earwax (may not be properly visible) or otherwise dirty.
3. Cleaning must be performed by an authorized service provider and is charged.
4. Earphones with the earphone duct filters removed.
5. Physical damage to the headphones caused by a fall or impact.
6. Damage caused by force majeure.

All information in this document is subject to change.

Documents / Resources

| INTEZE CLIQ TWS EARPHONES [pdf] User Manual
CLIQ TWS EARPHONES, TWS EARPHONES
---|---

References

• Why wireless TWS headphones | Intezze

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>