flowtoys 6142412774 Lumina Twirl Baton Instruction Manual
- June 4, 2024
- flowtoys
Table of Contents
flowtoys 6142412774 Lumina Twirl Baton
Overview
CAPSULE LIGHT
MicroUSB rechargeable light unit with super bright multicolor LEDs. Built-in
high-power Li-ion battery. See accompanying capsule light insert for
instructions.
CARBON FIBER SHAFT
Custom weaved 12mm carbon fiber with custom elastomer grip. Thin and
lightweight, yet super-strong and rigid.
ANTI-VIBRATION
Diffusive insert dampens vibration for quiet catches.
FLOWCAP
Thick, soft, durable silicone end cap with a rigid inner structure that snaps
securely onto our tubes and releases with a firm twist. The recessed end
button operates the light.
COMPOSITE CONNECTOR
3d-printed connectors screw into carbon fiber shaft to create a firm and
secure connection.
TUBES
Transparent yet virtually bulletproof polycarbonate. Connects to flow caps via
snap-button holes.
Presenting the world’s first durable, rechargeable illuminated twirling baton,
combining high-performance materials typically used in the aerospace and
racing industries. Thin and lightweight, yet super-strong and rigid carbon
fiber shaft for optimum comfort and performance. Transparent yet stiff and
impact-resistant polycarbonate end-tubes. Soft and clear, yet incredibly
durable silicone end caps for maximum glow and protection.
Made with the same high-tech materials that took humanity to space, your
illuminated flowtoys twirling baton will help take your baton practice to new
heights.
FOREVER FLOW LIFETIME WARRANTY
Flowtoys are designed to last you a lifetime, but nothing is indestructible, so we provide this warranty to enable you to freely find your flow. If you manage to break a flowtoys product, we offer free replacements on defective or non-working parts due to intended use, and 50% credit for products in any condition at any time. Battery depletion is normal wear & tear and is covered for free in the first 2 years and half-price/capsule after. If you need warranty support, please contact us at support@flowtoys.com.
Please check flowtoys.com for full warranty details. Flowtoys reserves the right to refuse coverage to anyone abusing this warranty. Please contact us before sending in your product, or it may be returned to the sender.
USING YOUR FLOWCAPS
ATTACHING/REMOVING FLOWCAPS FROM TUBES:
To detach, twist the cap firmly to release the internal snap buttons and pull
off the tube. To install, place cap over tube, push and twist until the
buttons click into the holes.
ATTACHING CAPSULES TO FLOWCAPS:
Insert capsule light into flow cap, button side in. Twist and push until light
clicks/settles into place. The seams of the capsule must be aligned with the
buttons inside the cap for it to fit in the tube.
Note:
The flow can connect very firmly to the end of the tube. To twist and remove,
you must grip the tube that the cap is connected to, not the carbon fiber
shaft.
Always check your connections before use
Tip:
If you find it difficult to remove the flow cap from the tube, check your hand
grip. You may be gripping the internal buttons against the tube! We provide a
grippy mat – you can use it to help by holding the tube with the grip mat
while twisting the cap off.
TROUBLESHOOTING
My flowcap won’t release from the tube
Make sure to grip the top end of your flowcap when removing it. If you grip
lower down the cap, the silicone can press against the tube, making it harder
to remove.
My capsule lights are falling out of the flowcap.
When installing capsule lights into a flow cap, make sure to TWIST until you
feel the light settle into place. You should be able to wiggle it left and
right a tiny bit.
CARING FOR YOUR BATON
Do not use glowsticks or WD-40 with tubing.
While polycarbonate is very strong, it breaks down in the presence of certain
esters, including those produced by chemical glowsticks, mineral spirits, and
WD-40. Do NOT put chemical glow-sticks into the tubes, otherwise, they can
become brittle and shatter.
Make sure all caps and connectors are fully secured before use!
Check that the buttons in your caps and connectors are fully clicked into
tubing holes.
Clean your grip!
The grip can wear out with use and is affected by oils from our skin. To
prolong the life of your grip, clean it after heavy use and before long
periods of storage. Use rubbing alcohol and a cloth, OR a cloth with warm
soapy water to remove oils from the grip. Wipe away any soap residue with
clean water.
If your flow caps get dirty, you can clean them with soap and warm water, or
put them in the wash with your laundry: air-dry, no heat!
Flowtoys makes more LED batons and we make more than batons! Visit us online to see our full line of lights, props, and gear for dance, twirling, juggling, and lifestyle. flowtoys.com.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>