flowtoys GLO-510 Composite Contact Wand Instruction Manual
- June 4, 2024
- flowtoys
Table of Contents
flow toys GLO-510 Composite Contact Wand
OVERVIEW
Presenting the world’s first durable, rechargeable LED contact levitation wand, combining high-performance materials typically used in the aerospace and racing industries. Thin and lightweight, yet super-strong and rigid carbon fiber shaft for optimum comfort and performance. Transparent yet stiff and impact-resistant polycarbonate end-tubes. Soft, clear durable silicone end caps for maximum glow and protection. Made with the same high-tech materials that took humanity to space, your illuminated flowtoys composite contact wand will help take your practice to new heights.
FOREVER FLOW LIFETIME WARRANTY
Flowtoys are designed to last you a lifetime, but nothing is indestructible,
so we provide this warranty to enable you to freely find your flow*. If you
manage to break a flowtoys product, we offer free replacements on defective or
non-working parts due to intended use, and 50% credit for products in any
condition at any time. Battery depletion is normal wear & tear and is covered
for free in the first 2 years and half-price/capsule after.
If you need warranty support, please contact us at
support@flowtoys.com.
- Please check flowtoys.com for full warranty details. Flowtoys reserves the right to refuse coverage to anyone abusing this warranty. Please contact us before sending in your product, or it may be returned to the sender.
USING YOUR END CAPS
REMOVING/ATTACHING FLOWCAPS FROM TUBES: To detach, twist firmly to release the buttons and pull. To install, place a cap over the tube, push and twist until the snap-buttons click into the holes. Tip: If you find it difficult to remove the flow cap from the tube, check your grip. You might be pressing the internal buttons against the tube!
ATTACHING CAPSULE LIGHTS TO FLOW CAPS
Insert capsule into flow cap, button side in. Twist and push until it settles.
The seams of the capsule must be aligned with the buttons inside the cap to
fit in the tube.
Note: The flow cap connects very firmly to the tube. To twist and remove,
you must grip the tube that the cap is connected to, not the carbon fiber
shaft.
Always check your connections before use.
TROUBLESHOOTING
My flow cap won’t release from the tube.
Make sure to grip the top end of your flow cap when removing it. If you grip
lower down the cap, the silicone can press against the tube, making it harder
to remove.
My capsule lights are falling out of the flow cap.
When installing capsule lights into a flow cap, make sure to TWIST until you
feel the light settle into place. You should be able to wiggle it left and
right a tiny bit.
My wand is always wonky!
Bumping the string, yourself, or other objects with the wand is a key cause of
wand-wonk. You can play with the work, but if you want to keep the wand
vertical, you will need to bring it back upright with your free hand and
gently set it down again. Start still and steady.
TIPS
Do not use glowsticks or WD-40 with tubing.
While polycarbonate is very strong, it breaks down in the presence of certain
esters, including those produced by chemical glowsticks, mineral spirits, and
WD-40. Do NOT put chemical glowsticks into the tubes, otherwise, they can
become brittle and shatter.
Make sure all caps are fully secured before use!
Check that the buttons in your caps are fully clicked into tubing holes.
Clean your grip!
The grip can wear out with use and is affected by oils from our skin. To
prolong the life of your grip, clean it after heavy use and before long
periods of storage. Use rubbing alcohol and a cloth, OR a cloth with warm
soapy water to remove oils from the grip. Wipe away any soap residue with
clean water. If your flow caps get dirty, you can clean them with soap and
warm water, or put them in the wash with your laundry: air-dry, no heat
!
Flowtoys make more than wands! Visit us at flowtoys.com to see our full line
of lights, props, and gear for dance, twirling, juggling, and lifestyle.