sensolus SNT3 ULTRA Sigfox Partner Network Instruction Manual

sensolus SNT3 ULTRA Sigfox Partner Network Instruction Manual

How to install the tracker

For alternative fixation methods such as magnets, glue and double sided tape please contact the Sensolus Help Desk.

support@sensolus.com or +32.9.298.09.43

Install Ultra tracker with bolts

1. Use the appropriate size of screws, it is recommended to use the M6 type and to use thread locking glue on the bolts. We recommend Loctite Thread Locker Blue 242.
2.  Protect the tracker casing appropriately: protect the casing with a washer and use a spring washer to mitigate the effects of vibration and temperature variations.
3. Don’t apply too much torque during the fixation: the maximum allowed torque is 3.5NM for an M6 screw used with a washer. Applying more torque may severely damage the tracker’s casing.

Install Ultra tracker with rivets

Use the appropriate size of rivets.

Choose the right length of the rivets.
The height of the casing where the mounting holes are located is 8mm.

We recommended to use rivets with a diameter of 5mm.

Install Compact tracker with bolts

1. Use the appropriate size of screws, it is recommended to use the M5 type and to use thread locking glue on the bolts. We recommend Loctite Thread Locker Blue 242.
2. Protect the tracker casing appropriately: protect the casing with a washer and use a spring washer to mitigate the effects of vibration and temperature variations.
3. Don’t apply too much torque during the fixation: the maximum allowed torque is 2.5NM for an M5 screw used with a washer. Applying more torque may severely damage the tracker’s casing.

Installation advice Ultra and Compact

• Avoid blocking the tracker’s view with metal or carbon fibre walls. They weaken or block the radiofrequency signals.

• Place the tracker has high as possible on the asset to ensure good network coverage.

• Make sure the mounting surface is flat and clean, for a strong and durable bond.

• Do not install the tracker on parts that receive frequent shocks or vibration.

• Install the tracker vertically, with the logo facing up.

• If your asset is handled in a rough environment, you can place the tracker in a protected location, but never with metal or carbonfibre above the tracker.

• Make sure the tracker has a clear view on the sky.

• Avoid placing the tracker in a place that can collect water.

• If you can’t install vertically, do not mount the tracker upside down.

• Do not install the Compact tracker on car’s dashboard. The maximum working temperature of the device will be exceeded, which leads to damage.
  

Tracker activation

 Activation of the trackers is preferably done with clear skies, and not inside (e.g. factory or warehouse). Trackers are not activated when delivered to your premises. Their subscription in the platform will start within six month of purchase.

• Hold a magnet for about 5seconds on top of the logo on the asset tracker.
  

• You will first see a red LED. Do not remove the magnet yet.
  

• When the green LED is blinking you can remove the magnet. Your tracker is ready for use.
  

Troubleshooting

1. Put the magnet on the tracker for less than 5 seconds
2. The possible LED feedback options are:

• Red LED: Tracker is not activated
  

• Green LED: Tracker is activated and working properly.
  

• No LED: tracker is not functioning (probably dead battery -> contact support)
  

• Red LED is blinking: Tracker is busy.
  

Force new configuration download on the tracker

• Hold a magnet for about 5 seconds on top of the logo on the asset tracker.
  You will see a green LED.
  

• You will see a red and green LED. Now remove the Magnet.
  

• Green LED is blinking for minimum 30 seconds.
  Your tracker is checking for new configurations.
  

• You see a red LED:
  No new configuration received
  

• You see a green LED: New configuration setting received.
  

SNT3 ULTRA: Battery Replacement

Step 1

• Make sure that the serial number and logo are facing the right way up.
• Then turn the tracker face down.
• Unscrew the 6 screws.

Tip: If using a power drill, use power setting 7, on low. ( Note: not all power drills have the same settings!)

Step 2

• Remove the back plate and the 6 screws.
  

Step 3

• Remove the batteries – pull them out of the connector.
  Tip: place a finger on the sponge to hold it in place
  

Step 4
Place the chip so the connector is towards the holder.

Step 5
Insert new batteries. Position the new batteries and make sure the batteries are in the center (on top of the sponge) – not too low or too high.

Step 9
The green light on the front of the tracker will rapidly flash green. From this moment, your asset tracker will start sending activity (movement) and GPS location. This information will be visible in the Sensolus Platform if you find yourself in an area with Sigfox communication network coverage.

References

• Sensolus, It Just Works! Industrial grade tracking solution.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>