Lowe s CFL-1174-01 Ceiling Fan With Lights Installation Guide

INSTALLATION MANUAL
CEILING FAN WITH LIGHTS
Model No.: CFL-1174-01

TOOLS REQUIRED

PACKING LIST

Installation kit

NOTE:

1. Some extra hardware may be included. The quantity is ted above s the number required for installation.
2. Parts “FF” have already been installed with Long Downrod Assembly. They need to be disassembled before installation.

INSTALLATION

1. Installing the Mounting Bracket

2. Assembling the Fan Step 1. Remove the clevis pin and “R” pin from the short downrod assembly.
   Step 2. Assemble the canopy and coupling cover.
   Step 3. Route wires from the fan through downrod assembly.
   Step 4. Insert clevis pin and “R” pin [FF] Step 5. Fix the set screw with a screwdriver.

3. Hanging the Fan Step 1. Lift the downrod into the mounting bracket. Rotate the downrod untilthe tab in the mounting bracket is seated in the fixation slot in the downrod ball.

4. Wiring Step 1. Insert the receiver to the mounting bracket.
   Step 2. Connect the wires from the fixture to the house supply wires with wire nuts (AA) , ground wire (green, green/yellow, or bare copper) to ground wire, neutral wire (white or blue) to neutral wire, and hot wire (black or brown) to the hot wire.
   Step 3. Wrap the connection with electrical tape.
   NOTE:
   1. This fan only needs one set of input wires (black, white, and ground wire). Both of the fan and lights will be controlled by the remote controller.
   2.This fan can only be connected to an on/off switch if you have one, not a dimmer switch.

5. Attaching the Canopy Step 1. Slide the canopy up to the ceiling and attach it to the mounting bracket with the screws provided.
   Step 2. Slide the canopy ring up to the canopy.
   Step 3. Slide the coupling cover downward to cover the yoke.

6. Assembling the Fan Blade S!ep 1. Align the fan blades with the mounting holes, fix them with blade screws (BB).
   NOTE:
   Make sure to assemble the blades in sequence and fasten the screws with equal force.

7. Assembling the Blade Arm Step 1. Loose the Blade Arm Screws from Fan Motor Assembly, then align the Blade Arms with the Mounting Holes, Fix them with Blade Arm Screws.

8. Assembling the Light Kit Mounting Plate Step 1. Attach Nipple (GG) to the Fan Motor Assembly with the Hex Nut (HH) provided.
   Step 2. Fix the light kit mounting plate on the lamp body with Screws

9. Install the Light Step 1. Connect the wire terminal to the interface on the LED Light Kit.

10. Install the Light Shade Step 1. Attach the Light Shade and Light Shade Cover through the Nipple (GG) with Light Shade Nut.

REMOTE CONTROL INSTRUCTIONS

1. Turn off power,

2. Natural wind, fan speed will change automatically with this function

3. 3.5.11.12.14(: Turn on the fan on 1/2/3/4/5/6 speed.

4. Turn off the fan.

5. Fan moves forwards or reversely.

6. (: Adjust the brightness of the light,

7. 15.16: Adjust the light color temperature,

8. : Turn on / off the light.
   Night mode, dim the lights.

9. Quick switch of the light color: warm white—>cool white—>daylight white.

10. : 2H for timing the fan.

REMOTE SIGNAL PAIRING:

If the remote control looses signal of the fan, press and hold the button  at the very beginning after it’s turned on from wall switch. After the fan light flashes or beeps, it’s done.

APP CONTROL INSTRUCTIONS

http://www.jasonghost.com/fanlamppro/

Install the “FanLamp Pro” app from Google Play, Apple App Store, or other app stores by scanning the QR code or searching for the app name.
Ensure that your phone is connected to the internet and Bluetooth enabled.

| Pairing: Click the Pair button within 5 seconds after turning on the fan from the wall switch. Once the fan flashes or beeps. it has been successfully paired with your phone and can now be controlled through the app.
---|---
| Slide the slider to change the fan speed
| Slide the slider to change the fan speed
| Slide to adjust the brightness of the light
| Quickly change color temperature’ White. Yellow. Natural “
| fan forward & Fan reverse
| Guiding style (not supported by this product)
| Timer
| Sleeping wind (Not applicable on this fan)
| Natural wind: Simulate natural wind and automatically adjust the wind speed

| Turn on/off the light
| Turn on/off the fan

Note:
Install the “FanLamp Pro” app from Google Play, Apple App Store, or other app stores by scanning the QR code or searching for the app name.
Ensure that your phone is connected to the internet and Bluetooth enabled.

Scan for Installation Video
https://youtu.be/8axtCvJOXVQ

APP Control Applicable
http://www.jasonghost.com/fanlamppro/

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>