ERMENRICH Verk LL100 Digital Level User Manual

: June 11, 2024
: ERMENRICH

Table of Contents

ERMENRICH Verk LL100 Digital Level
Product Information Ermenrich Verk LL100 Digital Level
Specifications
Product Usage Instructions
OVERVIEW
Getting started
Usage
Calibration
Specifications
Care and maintenance
Battery safety instructions
Levenhuk International Lifetime Warranty
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ERMENRICH Verk LL100 Digital Level

ERMENRICH-Verk-LL100-Digital-Leve-PRODUCT

Product Information Ermenrich Verk LL100 Digital Level

The Ermenrich Verk LL100 Digital Level is a versatile and easy-to-use tool for measuring slopes and angles with high accuracy. It is designed to be used in various applications, such as construction, carpentry, and DIY projects. The device comes with a magnetic base that allows for easy attachment to metal surfaces, and it has a clear LCD screen that displays measurement results in both inches per foot and millimeters per meter. The device also has an audible buzzer that alerts the user when it reaches a vertical position.

Specifications

Length Resolution : 1/8 inch per foot
Measuring Range : 0-90 degrees
Accuracy : +/- 0.2 degrees
Measurements: Inches per foot or millimeters per meter
Auto-off : Shuts down after 3 minutes of no activity
Operating Temperature Range : 32-122°F (0-50°C)
Storage Temperature Range: -4-140°F (-20-60°C)
Power Supply : 2 AAA batteries (not included)

Please carefully read the safety instructions and user manual before using this product. Keep away from children and use the device only as specified in the user manual.

Product Usage Instructions

Insert two AAA batteries into the battery compartment located on the back of the device.
To turn on the device, press the POWER/BUZZER button located on the front of the device. The device will automatically shut down after 3 minutes of no activity.
To zero the device, place it on a flat surface and press the ZERO button. The device will then reset to zero degrees.
To switch between measurement modes, press the MODE button. The device can measure slopes in both inches per foot and millimeters per meter.
To hold a measurement, press the HOLD button. The device will then display the current measurement on the screen until the HOLD button is pressed again.
The device has a magnetic base that can be attached to metal surfaces. To use this feature, place the device in the V-groove and press down firmly.
The device has an audible buzzer that alerts when it reaches a vertical position. To turn this function off, press the POWER/BUZZER button again.
After use, clean the device with a soft cloth and store it in a dry place.
For calibration instructions, please refer to the user manual.

OVERVIEW

ERMENRICH-Verk-LL100-Digital-Leve-FIG-1

POWER/BUZZER button
ZERO button
MODE button
HOLD button
Battery compartment
Magnetic base (in the V-Groove)

Please carefully read the safety instructions and the user manual before using this product. Keep away from children. Use the device only as specified in the user manual.

Getting started

Open the battery compartment cover and insert 2 AAA batteries. Close the cover.
Press the POWER/BUZZER button to turn the device on. Press and hold the POWER/BUZZER button for 3 seconds to turn the device off. The device will shut down in 3 minutes of no activity.
To measure, place the device on a flat surface.

Usage

When the device is on, it will display the current value in degrees. Press the MODE button to switch between °, %, mm/m, and in/ft. The slope is shown in inches per foot in 1/8-in increments.
The icon indicates either the horizontal or vertical position of the measured surface. The icons indicate that the measured surface deviates from the horizontal or vertical plane. The icon indicates whether the measured surface must be adjusted horizontally or vertically.
Hold function. To freeze the readings, press the HOLD button. The icon will appear on the screen. Press HOLD button again to return to measurement mode.
Acoustic alert. Press the POWER/BUZZER button. The icon will appear on the screen. The audible buzzer alerts when the device is within +/-1° of the horizontal or vertical position, the frequency of the sound differs when the device is near or far from the horizontal or vertical position, and alerts continuously when the device is in the horizontal or vertical position. Press the POWER/BUZZER button again to turn this function off.

Calibration

Press the POWER/BUZZER button to turn the device off. Place the device on a flat surface. Press and hold the MODE button and then press the POWER/BUZZER button until CAL1 appears on the display. Do not move the device and then press the MODE button. The icon CAL1 will start flashing and then the CAL2 icon will appear on the display. Rotate the device 180° and then press the MODE button. The CAL2 icon will start flashing. When CAL2 disappears, the calibration is complete. The calibration should be performed on a flat and smooth surface with a slope not exceeding 5°. If it exceeds 5°, the display will show the Erro icon, indicating that the calibration cannot be performed.

Specifications

Length 1000mm / 39.3in
Resolution 0.05°
Measuring range 0 to 360°
Accuracy ±0.1° at 0° and 90°, the rest: ±0.2°
Measurements °, %, mm/m, in/ft
Auto-off 3 min.
Operating temperature range 0…+40°C / 32…+104°F
Storage temperature range –10…+50°C / 14…+122°F
Power supply 2 pcs alkaline AAA batteries

The manufacturer reserves the right to make changes to the product range and specifications without prior notice.

Care and maintenance

Use the device only as specified in the user manual. Keep away from children. Do not try to disassemble the device on your own for any reason. For repairs and cleaning of any kind, please contact your local specialized service center. Protect the device from sudden impact and excessive mechanical force. Do not use the product in explosive environment, close to flammable materials. Store the device in a dry cool place. Only use accessories and spare parts for this device that comply with the technical specifications. Never attempt to operate a damaged device or a device with damaged electrical parts! If a part of the device or battery is swallowed, seek medical attention immediately.

Battery safety instructions

Always purchase the correct size and grade of battery most suitable for the intended use. Always replace the whole set of batteries at one time; taking care not to mix old and new ones, or batteries of different types. Clean the battery contacts and also those of the device prior to battery installation. Make sure the batteries are installed correctly with regard to polarity (+ and –). Remove batteries from equipment that is not to be used for an extended period of time. Remove used batteries promptly. Never short-circuit batteries as this may lead to high temperatures, leakage, or explosion. Never heat batteries in order to revive them. Do not disassemble batteries. Remember to switch off devices after use. Keep batteries out of the reach of children, to avoid risk of ingestion, suffocation, or poisoning. Utilize used batteries as prescribed by your country’s laws.

Levenhuk International Lifetime Warranty

All Levenhuk telescopes, microscopes, binoculars, and other optical products, except for their accessories, carry a lifetime warranty against defects in materials and workmanship. A lifetime warranty is a guarantee on the lifetime of the product on the market. All Levenhuk accessories are warranted to be free of defects in materials and workmanship for six months from the purchase date. The warranty entitles you to the free repair or replacement of the Levenhuk product in any country where a Levenhuk office is located if all the warranty conditions are met. For further details, please visit: www.levenhuk.com/warranty If warranty problems arise, or if you need assistance in using your product, contact the local Levenhuk branch.

Levenhuk Inc. (USA) : 928 E 124th Ave. Ste D, Tampa, FL 33612, USA, +1-813-468-3001, contact_us@levenhuk.com
Levenhuk Optics s.r.o. (Europe) : V Chotejně 700/7, 102 00 Prague 102, Czech Republic, +420 737-004-919, sales-info@levenhuk.cz
Levenhuk®, Ermenrich® are registered trademarks of Levenhuk, Inc. © 2006–2023 Levenhuk, Inc. All rights reserved. www.levenhuk.com