hygger HG079 LCD Display Quartz Heater User Manual
- June 13, 2024
- hygger
Table of Contents
hygger HG079 LCD Display Quartz Heater
Reminder
Please ensure that the controller remains dry, as it is not waterproof
Attention
- Place the heater fully submersible when it’s on duty. Unplug the heater and wait for 15 minutes before changing the water or removing it.
- Please make sure there is enough water flow and water circulation in your fish tank when using the heater.
- please do not bury the heating rod or use it near the sand.
- The actual temperature display tolerance range of ±10% is acceptable because this is the normal power consumption of electronic components within the allowable range.
PRODUCT FEATURES
- Made of durable and explosion-proof quartz glass for faster heat conduction.
- Features a high-quality LCD screen with a marquee display for easy temperature monitoring.
- Temp control range from 59°F (15°C) to a max of 93°F (34 °C); Temp accuracy: 0.1 °F (0.1 °C); Temp tolerance range: ±1 °F (±1 °C).
- Equipped with a reliable and safe external controller for convenient operation.
- Long press to switch between Fahrenheit (°F) and Celsius (°C) units. Press “SET” once to adjust the temperature by 0.5°F (or 0.5°C).
- Memory function, dry burning-resistant protection: Intelligent IC provides dry burning-resistant protection to ensure safety.
- The heat rod rings emit a warning signal when it is out of the water to prevent damage. The LCD screen displays fault codes “HH,” “LL,” or “EE” to indicate high/low temperature or probe faults.
- The hygger heating rod series offers a range of power options from 1 00W/200W/300W/ 500W to 800W to suit different aquarium sizes and heating needs.
PRODUCT SPECIFICATIONS
Model | Volt./ Freq | Cord length | Application: |
---|
HG079-100W
| | | 30~50Gal (100~200L)
HG079-200W
| | | 40~60Gal (150~230L)
| US Standard: AC110~120V/60Hz
EU/UK/AU Standard:
| ****
3.9ft+6.2ft (1.2m+1.9m)
|
HG079-300W
| 50~80Gal (200~300L)
| AC 220-240V/50Hz| |
HG079-500W
| 66~135Gal (250~343L)
HG079-800W
| | | 130~260Gal (490~980L)
Model
| ****
Temp accuracy
| Temp tolerance range| ****
Control range
| ****
Heater rod dimension
---|---|---|---|---
HG079-1 00W| ****
0.1°F (0.1°C)
| ****
±1 °F (±1°C)
| ****
59°F-93°F (15°C~34°C)
| ****
11.4″X2.2″X1 .1″ (29X5.5X3CM)
HG079-200W
HG079-300W
HG079-500W
HG079-800W
INSTRUCTIONS
- Install the sucking cup onto the heater rod, and turn it 90° to lock the cups.
- Fully submerge in water and connect the heater to the socket to use it directly.
MAINTENANCE
- Unplug or switch off all appliances in the aquarium before carrying out maintenance.
- Do not use detergents or other chemical cleaners.
- To clean the heater, unplug it first and then leave the heater in the tank for 15 minutes and remove it from the tank. Wash the heater in clean water.
- When reinstalling the heater, select your desired location and position the heater below the water.
- This appliance has no parts that can be repaired by users.
- For indoor use only, not in the bathroom.
TROUBLESHOOTING
Fault code | Explanation | Solutions |
---|
LL
| The tank temperature is lower than 59°F (15°c ).| ****
Raise the temperature
HH| The tank temperature reaches 94°F (35°C ).| ****
Lower the temperature
EE| Probe fault| Return to the seller
L1
| Out of the water and warning letters flashing “Auto shut off”| ****
Fully submerged in water
WARNING
To avoid possible electric shock, do not immerse the switch in the water. If
the switch falls into the water or becomes wet, do not touch it until you have
unplugged it. Basic safety precautions that should be observed are as follows:
-
Read and follow this user manual strictly.
-
DANGER- To avoid possible electric shock, special care should be taken since water is employed in the use of aquarium equipment. For each of the following situations,
do not attempt to repair yourself. Instead, return the heater to an authorized service facility for maintenance or discard it.- If the heater shows any sign of abnormal working, unplug the power and remove the heater from the water after 15 minutes.
- Carefully examine the heater after installation. It should not be plugged in iUhere is water on parts that are not intended to be wet.
- Do not operate the heater if it has a damaged cord or plug, is malfunctioning, dropped or damaged in any manner. The power cord of this heater cannot be replaced. If the cord is damaged, the heater should be discarded.
- To avoid the possibility of the heater plug getting wet, position the aquarium and its stand to one side of a wall-mounted outlet to prevent water from dripping onto the outlet or plug. A “drip loop”, shown in the figure below, should be arranged by the user for each cord, which connects the heater to the outlet. If an extension cord is used, the “drip loop” is the part of the cord below the level of the outlet or the connector that prevents water from traveling along the cord and coming in contact with the outlet. If the plug or outlet does get wet, DO NOT unplug the cord. Disconnect the fuse to the circuit breaker that supplies power to the heater. Then unplug and examine for the presence of water in the outlet. If you are not sure, consult a certified electrician.
-
Close supervision is necessary when the heater is used near children.
-
This heater is not allowed to be used by persons (including children) with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the heater by a person responsible for their safety.
-
To avoid injury, do not contact moving or hot parts.
-
Always unplug the heater from the outlet when not in use, before putting on or taking off parts, maintenance, or placing hands in the water. Never yank the cord to pull the plug from the outlet. Grasp the plug and pull to disconnect.
-
Do not use the heater for other than intended use. The use of attachments not recommended or sold by the appliance manufacturer may cause an unsafe condition and will void the warranty.
-
Do not install or store the heater where it will be exposed to extreme weather or temperatures below freezing.
-
Only use the heater in freshwater or saltwater, do not use it in other liquids.
-
Make sure the heater is securely installed before operating it.
-
Read and observe all the important notices on the heater.
-
If an extension cord is necessary, a cord with a proper rating should be used, such as rated amperes or watts. A cord rated for fewer amperes or watts than the heater rating may overheat. Care should be taken to arrange the cord so that it will not be tripped over or pulled.
-
The 2-conductor power cord has a polarized plug (one blade is wider than the other.) As a safety feature, this plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Never use it with an extension cord unless the plug can be fully inserted. Do not attempt to defeat this safety feature.
-
The heater is intended FOR HOUSEHOLD USE ONLY.
-
SAVE THIS USER MANUAL.
ATTENTION
-
Please check all the items to inspect their condition when unboxing the package.
-
Please read this user manual carefully before using it and follow it strictly.
-
Please choose a heater rated for your aquarium.
-
Please place the heating rod in the way of water flow and don’t bury it in the substrate.
-
It is suggested that the heater is submerged more than 5 inches below the water.
-
Please make sure the heating rod is fully submerged when it’s on duty. Unplug the heater and wait for 15 minutes before changing the water or removing the heater.
-
Please mind that the heater can be turned off automatically when
exposed to air, but it is a last resort and should be avoided. -
After using the heater for a while, calcium carbonate contained in algae or moss may clump and adhere to the heating rod.
-
If dirt adheres to the heating rod, use a sponge or cloth and water to wipe it. Do not use alcohol or other chemicals as this may damage the heater and harm the fish or other livestock.
-
If you use the heater for a prolonged period with dirt adhered to the heating element, please be aware that failure may occur due to the inability to control the temperature correctly.
-
Please place the heating rod far away from the magnetic brush since the magnet will possibly damage the heating element.
-
There will be a little mist on the inner wall of the tube while heating, and it will disappear slowly after the heating stops, which means it’s a normal phenomenon. So you don’t have to worry about it, it is a safe and double-protected product that has passed the UL certification.
ONE-YEAR LIMITED WARRANTY
This product MUST be purchased from an authorized hygge reseller. Visit our
website for a list of unauthorized resellers. hygger warrants this product
against defects in materials and worksmanship for ONE (1) YEAR from the date
of the original retail purchase and is non-transferable. Warranty on all
products, including aquariums. However, it is limited to the replacement of
the products and does not cover fish loss, personal injury, property loss, or
direct, incidental, or consequential damage caused by using this product.
Note : hygger One-year Limited Warranty does not cover damage caused by
the following: improper installation, saltwater corrosion, electrical surges,
or modifications. Additionally, products that have been refunded are also not
covered under the warranty.
If you discover a defect, please contact Hygger, who will, at its option, repair or replace the product at no charge, provided that you return it during the warranty period. A copy of the bill of sale is required as proof of the original purchase date in the event of the product needing repairs within the warranty period. hygger does not warrant any products that aren’t hygger’s. This warranty does not apply if the product has been damaged by accident, abuse, misuse, or misapplication, or modified without the written permission of Hygger.
DISPOSAL
Do not dispose of this product as unsorted municipal waste. Collection of such
waste separately for special treatment is necessary. This product has to be
disposed at an authorized place for the recycling of electrical and electronic
appliances rather than being disposed of together with the domestic waste.
Collecting and recycling waste is a way of saving natural resources. So,
please consult with your local seller to make sure the product is disposed of
in an environmentally friendly way.
PACKING LIST
- 1 x Heater rod
- 1 x Controller holder
- 3x Suction cups (includes 1 pc spare part)
- 1x Hook
CONTACT INFORMATION
Distributed by: Hygger Aquarium, Inc.
Chino, CA 91710
Contact us at www.hygger-online.com
Email: mago@hygger-online.com
Trademarks of Shenzhen Mago Trading Co., Ltd Bantian Group Business Center,
Longgang, Shenzhen City, China
All Rights Reserved
Made in China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>