BEITONG BTP-2585NS Asura 2 Game Controller Multi Mode User Manual
- October 30, 2023
- BEITONG
Table of Contents
BEITONG BTP-2585NS Asura 2 Game Controller Multi Mode
FCC STATEMENT
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in 3 residential installations. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harm Ul interference to radio communications. However, there is no IS guarantee that interference will not occur a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user iS encouraged to try to correct the interference Dy one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.The device has been evaluated to meet general RF exposure requirements
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
KEYS INTRODUCTION
- indicator light 1
- indicator light 2
- indicator light 3
- indicator light 4
- SELECT
- TURBO
- HOME
- START
- Left Stick/LS (Press down)
- D-Pad
- Right Stick/RS (Press down)
- ABXY
TURN ON AND OFF INSTRUCTIONS
Turn on
Press LOGO button
Turn off
Press and hold Select + B for 3 seconds
- When the controller is working, it will automatically shut down idle for 10 minutes.
- When the controller is not working, IC will automatically shut down In idle for 120 seconds.
- When the battery is low, the controller will automatically shut down.
Notice!
When the battery power of the controller is less than 30%, the mode indicator
light flashes quickly and the vibration is turned off, please charge as soon
as possible.
TUTORIAL FOR CONNECTION
Press RB + SELECT + RS + LOGO button to turn on the controller, pairing information can be actively cleared.
Connect to computer
Use the data cable to connect the controller to the USB port of the computer,
and then tap the LOGO button to turn it on. Then the device vibrates and the
indicator light 2 is on, the connection is complete.
- The controller does not support Bluetooth wireless connection of the computer currently,
Connect to TV/Smartphone
- Press and hold the LOGO Button + B in the power-off state to turn the controller into the BFM mode, while indicator light 3 will flash. Press and hold LOGO Button + B in the power-on state switch to the BFM mode, while the indicator light 3 will flash.
- 0pen UD the Bluetooth function interface of the TV/Smartphone, search or select and connect the device” BEITONG 2585NS BFM”.
- Wait for a while, the controller vibrates and the indicator light 3 is on, the connection is complete.
Connect to Nintendo Switch
Turn on the Switch, open up the “Controller and Sensors*, “Change Grip/Order”;
Press the LOGO Button of the controller to turn it on, and then press and hold
LB + RB until the pairing interface appear on Switch ,and then press the A
button to pair; After the pairing is successful, just turn on the controller
and it will automatically connect.
Connection failed:
90 into system settings and select controllers and sensors. scroll down to
find and click disconnect controllers. press and hold the X button on the joy-
con at this interface until the prompt has been disconnected from the
controller; Press the RB + SELECT Button + RS + LOGO Button to turn on the
controller until the indicator light flashes, press and hold the SELECT + B to
turn off the controller. After that, turn it on again, and press and hold LB +
RB to re-pair; f the controller has been already once connected to the Switch,
re-connect only by pressing the LOGO button of the controller next time in
state of no device connected. After the connection is successful, the
corresponding button of the controller is as follows:
OTHER FUNCTIONS
Toggle the A/B button value
- Press the LOGO button+ B to switch the controller’s working mode and different key values will be automatically switched.
- NS mode: indicator light on, A means A, B means B
- Wired PC Mode: indicator light 2 on, A means B, B means A
- BFM Mode: indicator light 3 on, A means B, B means A
Button function description in NS mode
Motion Sensing Adjustment
- The Motion Sensing function only supports the connection of the Nintendo Switch
- Turbo + D-Pad LEFT, Sensitivity reduced
- Turbo + D-Pad RIGHT. Sensitivity enhancement
Turbo Function Settings
- Press the Turbo button in the power-on state, and then press any action button to achieve the Turbo function, repeat this operation to cancel the Turbo function.
Action button refers to A,B,X,Y,L,B,R,B,L,T,R,T
Vibration Intensity Adjustment
- + Turbo + D-Pad UP. Vibration intensity enhances
- Turbo + D-Pad DOWN, Vibration intensity weakens
PRODUCT SPECIFICATION
Warranty Card
Dear customer,
Thanks for using BEITONG gaming peripheral products. We focus on providing
gamers with better gaming experience, please provide the information through
your email for customer service:
- Purchasing Channel
- Buyer ID
- Order Number
- Product Model
Please provide the below information for us according to the product situation:
- Please provide service season
- The function is not 9000
- Bad appearance
- Can not use in my device
- Can not play the game want to play
- Other
- Please provide the service you need
- Replacement
- Repairing
- Return
- Other
Customer service contact: beitong-oversea@betop-cn.com We also welcome our customers to provide suggestions so that to improve and upgrade our product. Any a00d ideas for our products, please feel free to contact US it’s very grateful. Meanwhile, we’ll select the customer who in high-quality advice to experience our new products for the free opportunity. Sincerely BEITONG Customer Service Team
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>