B-TECH BT899XL Projector Mount Ceiling Installation Guide

B-TECH BT899XL Projector Mount Ceiling

SPECIFICATIONS

• Universal ceiling mount for projectors up to 25kg (SSlbs)
• Can be mounted flush to the ceiling or onto a 050mm extension pole or 1 ½” NPT pipe (not included)
• Features tilt, roll and swivel adjustments
• Optional micro-adjustment for perfect alignment of projected images
• Maximum distance between any two fixing points: 493mm
• Suitable for projectors using M2.5, M3, M4, MS and M6 fixings
• All mounting hardware & fixings included

INSTALLATION SAFETY INSTRUCTIONS

CAUTION: This mount is intended for use only with the maximum weights indicated. Use with equipment heavier than the maximum indicated may result in instability causing possible injury.

Do not attempt to install this product until all instructions and warnings have been read and properly understood.
Please keep these instructions for future reference.
Please check carefully to make sure there are no missing or defective parts – defective parts must never be used. B-Tech AV Mounts, its distributors and dealers are not liable or responsible for damage or injury caused by improper installation, improper use or failure to observe these safety instructions. In such cases, all guarantees will expire.

General

B-Tech AV Mounts recommends that a professional AV installer or other suitably qualified person install this product. Great care must always be taken during installation as most AV equipment is of a fragile nature, possibly heavy and easily damaged if dropped.
If you do not fully understand the instructions or are not sure how to install this product safely, then please consult a professional for advice and/or to install this product for you. Failure to mount this product correctly may cause serious injury or death, both during installation and at any time thereafter.
Do not mount any AV equipment that exceeds the specific weight limit of the product you are installing. This weight limit will be clearly stated on each product and its packaging and will vary from product to product.

Product location

Please pay careful attention to where this product is located. Check load capacity of the ceiling prior to installation as some surfaces are not suitable for installation. Designed for indoor use, this mount is suitable for public or home installation If located in a public or frequently populated area ensure that the product is out of the immediate reach of people. If any AV equipment is to be suspended over the likely path or location of people then great care should be taken to secure all parts of the installation from falling.
When drilling holes it is essential to avoid contact with electrical cables and water or gas pipes contained within. Use of a good quality live wire detector and hidden object locator is therefore recommended.
Only drill into structures when you are sure it is safe to do so.

Fixing hardware

It is highly recommended that all fixing screws be used where supplied and that the purpose of all other fixing hardware is fully understood. In some cases more AV equipment fixing hardware will be supplied to accommodate different models of equipment and set up configurations. The installer must be satisfied that any supplied fixing hardware is suitable for each specific installation. The fixing kit supplied with the product may not be suitable for all ceilings.
If any fixing screws or included hardware are deemed not sufficient for a safe installation then please consult a professional or your local hardware store.

Hazard limitation

When routing cables take advantage of any built in cable management features that the product might provide and ensure that all cables are tidy and secure. Check to see that any moving aspect of the product can do so unhindered by any cabling. Some products have moving parts and the potential to cause injury through the crushing or trapping of fingers or other body parts. Particular attention to the nature of moving parts is required especially when assembling installing and adjusting during set up. Immediately after installation double- check that the work done is safe and secure. Double-check all necessary fixings are present and are of ample tightness. It is recommended that periodic inspections of the product and its fixing points are made as frequently as possible (no more than 6 months apart) to ensure that safety is maintained.
If in doubt consult a professional AV installer or other suitably qualified person.

PARTS LIST

PLEASE KEEP THIS FDR FUTURE REFERENCE

INSTALLATION TOOLS REQUIRED

• Drill 10mm (7/16″) masonry bit or 6mm (1/4″) wood bit
  

• Pencil

• 13mm (1/2″) spanner or socket
  

• Cross head Screwdriver

ITEM

| PART NAME|

QTY

---|---|---

1

|

CEILING PLATE

| 1
2| JOINING PLATE|

1

3

|

SWIVEL PLATE

| 1
4| CAROUSEL PLATE|

1

5

|

LONG LEG

| 4
6| SHORT LEG|

4

7

|

MOUNTING SCREW

| 4
8| M8 x 16mm HEX SCREW|

1

9

|

M8 T2mm PLASTIC WASHER

| 1
10| M8 NYLOC NUT|

1

11

|

M6 x 8mm SCREW

| 4
12| M6 Tl mm METAL WASHER|

4

13

| M6 x 12mm PIN HEX SCREW| 8
14| M6 T1.2mm METAL WASHER|

6

15

| M6 x 20mm GRUB SCREW|

1

16

| ADJUSTMENT BRACKET| 2
17| M4 x 30mm PIN HEX SCREW|

2

18

| M4 Tl mm METAL WASHER| 2
19| M4 T1.6mm PLASTIC WASHER|

2

20

| M4 NYLOC NUT| 2
21| POLE ADAPTOR|

1

22

| Ml Ox 6mm GRUB SCREW| 2
23| M8 x 60mm PIN HEX SCREW|

1

24

| 3AF HEX KEY| 1
25| SAF PIN HEX KEY|

1

INTERFACE KIT

A

| M2.5 x 25mm SCREW| 4
B| M3 x 12mm SCREW|

4

C

| M3 x 25mm SCREW| 4
D| M4x 12mm SCREW|

4

E

| M4x 25mm SCREW| 4
F| MS x 12mm SCREW|

4

G

| MS x 25mm SCEW| 4
H| M6x 12mm SCREW|

4

I

| M6 x 25mm SCREW| 4
J|

M3 METAL WASHER

|

4

K

| M4 METAL WASHER| 4
L| TID6.5 Tl 2mm SPACER|

4

FIXING KIT

Al

| M8 x 50mm COACH SCREW|

4

A2

| M8 OD18 Tl.5mm WASHER|

4

A3

| N° 10 x 50mm WALL PLUG|

4

Suitable for loads up to 25kg (SSlbs)

INSTALLATION INSTRUCTIONS

ATTACH INTERFACE TO PROJECTOR

Line up item 5 with the projector fixing holes and fix interface assembly to the projector using the interface kit (items A – I).

OPTIONAL ADD MICRO-ADJUSTMENT

For a precise post-installation alignment of the tilt or roll, the micro- adjustment can be installed. Note: If the micro-adjustment is not required proceed to Step 3.

MOUNT CEILING PLATE TO CEILING

Fix item 1 to the ceiling using items A 7, A2 & A3.

HOOK PROJECTOR ONTO CEILING PLATE

Hook item 2 onto item 1 and secure using items 13 & 14.

ADJUSTING THE PROJECTOR

To tilt/roll, loosen items 13, adjust and re-tighten. To swivel, loosen item 70, adjust then re-tighten.

MICRO-ADJUSTMENT (IF INSTALLED

i. Using item 25, loosen item 13 by one turn.

ii. Adjust item 17 to tilt or roll the projector.

POLE MOUNTING OPTIONS

NPT PIPE MOUNTING

Mounting to 1 ½” NPT pipe.

SYSTEM 2 ADAPTOR

Use item 21 to mount the projector to a B-Tech 050mm pole.

TYPICAL POLE MOUNTED INSTALLATION

SYSTEM2
Use B-Tech’s System 2 range to mount the projector with extended ceiling drops.

DIMENSIONS

CONTACT: info@btechavmounts.com

©2020 B-Tech AV Mounts. All rights reserved.
B-Tech AV Mounts is a division of B-Tech International Design and Manufacturing Ltd.
B-Tech AV Mounts and the B-Tech logo are registered trade marks.
All other brands and product names are trademarks of their respective owners.
Photographs are for illustrative purposes only. E&OE.
AMA-BT899XL-V1.1-0121-03 MADE IN THE P.R.C.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>