B-TECH BT8601 Universal Flat Screen Wall Mount with Tool-Less Height Adjustment Installation Guide
- June 4, 2024
- B-TECH
Table of Contents
B-TECH BT8601 Universal Flat Screen Wall Mount with Tool-Less Height
Adjustment
SPECIFICATIONS
- Recommended for screens up to 65″ Max load:
- BT8601-01 19kg – 36kg (42lbs – 79lbs) BT8601-02 37kg – 62kg (81lbs -136lbs) BT8601-03 63kg – 80kg (139lbs -176lbs)
- Suitable for displays with VESA® & non-VESA fixings up to 600 x 400mm
- Tool-less height adjustment of the screen
- Height adjustment range: 400mm
- Mounts screen 124mm from wall
- Simple hook-on installation, all mounting hardware included
BT8601-01 BT8601-02 BT8601-03
INSTALLATION SAFETY INSTRUCTIONS
CAUTION
This mount is intended for use only with the maximum weights indicated. Use
with screens heavier than the maximum indicated may result in instability
causing possible injury. Do not attempt to install this product until all
instructions and warnings have been read and properly understood. Please keep
these instructions for future reference. Please check carefully to make sure
there are no missing or defective parts – defective parts must never be used.
B-Tech AV Mounts, its distributors, and dealers are not liable or responsible
for damage or injury caused by improper installation, improper use, or failure
to observe these safety instructions. In such cases, all guarantees will
expire.
General
B-Tech AV Mounts recommends that a professional AV installer or other suitably
qualified person install this product. Great care must always be taken during
installation as most AV equipment is of a fragile nature, possibly heavy and
easily damaged if dropped. If you do not fully understand the instructions or
are not sure how to install this product safely, then please consult a
professional for advice and/or to install this product for you. Failure to
mount this product correctly may cause serious injury or death both during
installation and at any time thereafter. Do not mount any AV equipment that
exceeds the specified weight limit of the product you are installing. This
weight limit will be clearly stated on each product and its packaging and will
vary from product to product.
Product location
Please pay careful attention to where this product is located. Check the load
capacity of the wall prior to installation as some walls are not suitable for
installation. Designed for indoor use, this mount is suitable for public or
home installation If located in a public or frequently populated area ensure
that the product is out of the immediate reach of people. If any AV equipment
is to be suspended over the likely path or location of people then great care
should be taken to secure all parts of the installation from falling. If you
install this product on drywall it must be securely fixed to a wooden stud,
concrete block, or other permanent structure behind the drywall board.
Installing on drywall boards alone will not support the weight of most AV
equipment. When drilling holes in walls it is essential to avoid contact with
electrical cables and water or gas pipes contained within. Use of good quality
live wire detector and hidden object locator is therefore recommended. Only
drill into structures when you are sure it is safe to do so.
Fixing hardware
It is highly recommended that all fixing screws be used where supplied and
that the purpose of all other fixing hardware is fully understood. In some
cases, more AV equipment fixing hardware will be supplied to accommodate
different models of equipment and set up configurations. The installer must be
satisfied that any supplied fixing hardware is suitable for each specific
installation. If any fixing screws or included hardware are deemed not
sufficient for a safe installation then please consult a professional or your
local hardware store.
Hazard limitation
When routing cables take advantage of any built-in cable management features
that the product might provide and ensure that all cables are tidy and secure.
Check to see that any moving aspect of the product can do so unhindered by any
cabling. Some products have moving parts and the potential to cause injury
through the crushing or trapping of fingers or other body parts. Particular
attention to the nature of moving parts is required especially when assembling
installing and adjusting during set up. Immediately after installation double-
check that the work done is safe and secure. Double-check all necessary
fixings are present and are of ample tightness. It is recommended that
periodic inspections of the product and its fixing points are made as
frequently as possible to ensure that safety is maintained. If in doubt
consult a professional AV installer or another suitably qualified person.
BT8601 PARTS LIST
| REF | PART NAME | QTY |
|---|---|---|
| 1 | WALL PLATE | 1 |
| 2 | BALANCE BOX | 1 |
| 3 | ADAPTOR PLATE | 2 |
| 4 | MOUNTING PLATE | 1 |
| 5 | INTERFACE ARM | 2 |
| 6 | VESA 600 ADAPTOR | 2 |
| 7 | M8 x 12mm CSK SCREW | 4 |
| 8 | M8 x 16mm CSK SCREW | 4 |
| 9 | M8 x 8mm SCREW | 4 |
| 10 | WASHER | 4 |
| 11 | HEX KEY | 1 |
FIXING KIT
A| M4 x 12mm SCREW| 4
B| M4 x 25mm SCREW| 4
C| M4 x 40mm SCREW| 4
D| M6 x 16mm SCREW| 4
E| M6 x 25mm SCREW| 4
F| M6 x 40mm SCREW| 4
G| M8 x 16mm SCREW| 4
H| M8 x 25mm SCREW| 4
I| M8 x 40mm SCREW| 4
J| 5mm SPACER| 4
K| 13mm SPACER| 4
L| 24mm SPACER| 4
M| MULTIWASHER| 4
WALL FIXING KIT
A1| COACH SCREW| 4
A2| WASHER| 4
A3| WALL PLUG| 4
INSTALLATION TOOLS REQUIRED
INSTALLATION INSTRUCTIONS
MOUNT WALL BRACKET
- Measure the mounting height from the floor*.
- Mark and then drill holes to mount item 1.
- Mount item 1 level to the wall.
Note: Use the mounting height calculator on: www.balancebox.eu to determine the height of the wall bracket.
WALL
MOUNT BALANCEBOX® TO WALL BRACKET
Hook item 2 onto item 1.
Note: Ensure the locking screws at the top of item 2 are unlocked.
SECURE AND LEVEL BALANCE BOX
- Tighten locking screws at the top of item 2.
- Vertically level the BalanceBox by using the leveling screws at the bottom it item 2.
ATTACH ADAPTOR PLATES TO THE BALANCE BOX
- Fix item 3 to item 2 using item 8.
ATTACH MOUNTING PLATE
Attach item 4 to item 3 using items 9 & 10.
FIX INTERFACE ARMS TO REAR OF SCREEN
Fix items 5 to the back of the screen using the interface kit (items A-M).
Note: Ensure item 5 is positioned the correct way around.
Using 600mm Adaptor Arms
Portrait mounting assembly shown
- Attach item 6 to item 5 using item 7.
- Attach item 6 to rear of screen using the interface kit (items A-L).
HOOK SCREEN ONTO MOUNTING PLATE
- Hook screen onto item 4.
SCREEN ADJUSTMENT (OPTIONAL)
To level the screen, use the height adjustment screws at the top of item 5.
LOCK SCREEN ONTO MOUNTING PLATE
Lock screen onto item 4 using the locking screws at the bottom of item 5.
BALANCE SCREEN TO ENABLE HEIGHT ADJUSTMENT
To counterbalance the screen use a drill driver with a 10mm socket at a low
torque setting.
- On the top of item 2 turn the left spring tension point counter-clockwise for 3 seconds.
- Turn the right spring tension point counter-clockwise for 3 seconds.
- Repeat steps (i) and (ii) until the screen is nearly balanced.
- Fine tune the spring tension points until item 2 can hold the weight of the screen at every height (this may take some time).
FRONT VIEW
HEIGHT OPTIONS
BACK VIEW
SIDE VIEW
TOP VIEW
THESE INSTRUCTIONS ARE INTENDED AS A GUIDE ONLY AND B-TECH ACCEPTS NO LIABILITY FOR THE ACCURACY OF THE INFORMATION CONTAINED IN THIS DOCUMENT.
CONTACT:
info@btechavmounts.com
©2019 B-Tech International Design & Manufacturing Ltd. All rights reserved. B-Tech AV Mounts is a division of B-Tech International Design & Manufacturing Ltd. B-Tech AV Mounts and the B-Tech logo are registered trade marks. All other brands and product names are trademarks of their respective owners. Photographs are for illustrative purposes only. E&OE. AMA-BT8601-V1-1119-110 MADE IN VIETNAM For More Information Visit www.btechavmounts.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>