B-TECH BT7004 Bolt Down Digital Signage Mount Installation Guide
- June 4, 2024
- B-TECH
Table of Contents
BT7004
bolt down Digital Signage mount
WITH SCREEN ENCLOSURE
INSTALLATION GUIDE
SPECIFICATIONS
- Max load: 50kg (110lbs)
- Suitable for screens with VESA® and non-VESA fixings
- Base dimensions: W: 240mm D: 240mm
- Vented top and bottom panels allow airflow to and from the device
- Integrated cable management
- Simple ‘hook-on’ screen installation with all mounting hardware included
INSTALLATION SAFETY INSTRUCTIONS
CAUTION: This mount is intended for use only with the maximum weights
indicated. Use with equipment heavier than the maximum indicated may result in
instability causing possible injury.
Do not attempt to install this product until all instructions and warnings
have been read and properly understood. Please keep these instructions for
future reference. Please check carefully to make sure there are no missing or
defective parts – defective parts must never be used. B-Tech AV Mounts, its
distributors, and dealers are not liable or responsible for damage or injury
caused by improper installation, improper use, or failure to observe these
safety instructions. In such cases, all guarantees will expire.
General
B-Tech AV Mounts recommends that a professional AV installer or other suitably
qualified person install this product. Great care must always be taken during
installation as most AV equipment is of a fragile nature, possibly heavy and
easily damaged if dropped. If you do not fully understand the instructions or
are not sure how to install this product safely, then please consult a
professional for advice and/or to install this product for you. Failure to
mount this product correctly may cause serious injury or death, both during
installation and at any time thereafter. Do not mount any AV equipment that
exceeds the specified weight limit of the product you are installing. This
weight limit will be clearly stated on each product and its packaging and will
vary from product to product.
Product location
Please pays careful attention to where this product is located. Designed for
indoor use, this mount is suitable for public or home installation. Check the
load capacity of the floor prior to installation as some surfaces are not
suitable for installation. When verifying the stability of the structure,
consider the following external factors: The strength of the floor, exposure
to sudden and severe wind, and danger arising from contact with people and/or
objects (eg installations in passageways, emergency exits), if located in a
public or frequently populated area ensure that the product is out of the
immediate reach of people. When drilling holes it is essential to avoid
contact with electrical cables and water or gas pipes contained within. Use of
good quality live wire detector and hidden object locator is therefore
recommended. Only drill into structures when you are sure it is safe to do so.
Fixing hardware
It is highly recommended that all fixing screws be used where supplied and
that the purpose of all other fixing hardware is fully understood. In some
cases, more AV equipment fixing hardware will be supplied to accommodate
different models of equipment and set up configurations. The installer must be
satisfied that any supplied fixing hardware is suitable for each specific
installation. If any fixing screws or included hardware are deemed not
sufficient for a safe installation then please consult a professional or your
local hardware store.
Hazard limitation
When routing cables take advantage of any built-in cable management features
that the product might provide and ensure that all cables are tidy and secure.
Check to see that any moving aspect of the product can do so unhindered by any
cabling. Some products have moving parts and the potential to cause injury
through the crushing or trapping of fingers or other body parts. Particular
attention to the nature of moving parts is required especially when assembling
installing and adjusting during setup. Immediately after installation double-
check that the work done is safe and secure. Double-check that all necessary
fixings are present and are of ample tightness. It is recommended that
periodic inspections of the product and its fixing points are made as
frequently as possible (no more than 6 months apart) to ensure that safety is
maintained. If in doubt consult a professional AV installer or another
suitably qualified person.
BT7004 PARTS LIST
PLEASE KEEP THIS FOR FUTURE REFERENCE
Note: Components supplied may differ from what is shown depending on the type and size of the display being installed.
| ITEM | PART | DESCRIPTION | QTY |
|---|---|---|---|
| BASE | Al | BOLT DOWN BASE | 1 |
| A2 | M8 x 35mm CSK SCREW | 4 | |
| A3 | 5AF HEX KEY | 1 | |
| COLUMN | B1 | VERTICAL COLUMN | 1 |
| B2 | END CAP | 1 | |
| B3 | CABLE COVER | 3 | |
| B4 | PLASTIC SLOT INSERT | 4 | |
| MOUNTING BRACKET | Cl | MOUNTING BRACKET | 1 |
| C2 | M8 SLIDING INSERT | 4 | |
| C3 | M8 x 12mm SCREW | 4 | |
| C4 | 5AF HEX KEY | 1 | |
| COLUMNFIXINGS | D1 | M8 SLIDING INSERT | 4 |
| D2 | M8 x 12mm SCREW | 4 | |
| RAIL | El | MOUNTING RAIL | 1 |
| E2 | END CAP | 2 | |
| ARMS | Fl | SCREEN INTERFACE ARM | 2 |
| F2 | 5AF LONG HEX KEY | 1 | |
| SCREEN FIXING KIT | F3 | M4 x 12mm SCREW | 4 |
| F4 | M4 x 25mm SCREW | 4 | |
| F5 | M4 x 40mm SCREW | 4 | |
| F6 | M6 x 16mm SCREW | 4 | |
| F7 | M6 x 25mm SCREW | 4 | |
| F8 | M6 x 40mm SCREW | 4 | |
| F9 | M8 x 16mm SCREW | 4 | |
| F10 | M8 x 25mm SCREW | 4 | |
| Fl 1 | M8 x 40mm SCREW | 4 | |
| F12 | MULTIWASHER | 4 | |
| F13 | 5mm SPACER | 4 | |
| F14 | 13mm SPACER | 4 | |
| F15 | 24mm SPACER | 4 | |
| SCREEN ENCLOSURE | G1 | LEFT COVER PLATE | 1 |
| G2 | RIGHT COVER PLATE | 1 | |
| G3 | M6 x 20mnn CAP HEAD SCREW | 2 | |
| G4 | M8 x 1 Omm HEX SCREW | 8 | |
| G5 | M8 SLIDING INSERT | 8 | |
| G6 | 5AF HEX KEY | 1 |
INSTALLATION TOOLS REQUIRED
INSTALLATION INSTRUCTIONS
-
ATTACH COLUMN TO BASE
Fix item, Al, to item 81 using item A2.
-
BOLT STAND ON THE FLOOR
Pre-drill holes in the floor and use suitable floor fixings (not supplied) fix item Al to the floor.
-
ATTACH MOUNTING BRACKET TO RAIL
i. Insert 4 x item C2 into item E1 (2 in the top channel, 2 in the bottom channel).
ii. Fix item C1 centrally to item E1 using item C3.
-
FIX RAIL TO COLUMN
i. Insert 4 x item D1 into item B1 (2 in each channel).
ii. Attach item C1 to item B1 using item D2. Leave a 6mm gap at top of the column.
-
ATTACH INTERFACE ARMS TO SCREEN
Fix item Fl to the rear of the screen using items F3 – F15.
Note: Ensure the arms are facing the correct way round and the same holes are used on both arms.
PORTRAIT MOUNTING
-
MOUNT SCREEN ONTO RAIL
i. Hook screen onto item El using items Fl.
ii. Secure screen to stand by tightening the safety skews on the bottom of items Fl.
-
FIX SCREEN ENCLOSURE
i. Insert 8 x item G5 into item E1 (4 in the top channel, 4 in the bottom channel) and position as shown in fig. 1.
ii. Attached is item E2 to the ends of item E1.
iii. Connect items G1 & G2 around the screen and secure to item E1
using item G4.
-
LOCK SCREEN ENCLOSURE Fix items G1 & G2 together at the top and bottom using item G3.
-
ATTACH COVER PLATES Once cables have been routed through the stand, attach items 82, 83 & 84 to item 81.
CONTACT:
info@btechavmounts.com
©2021 B-Tech AV Mounts. All rights reserved.
B-Tech AV Mounts is a division of B-Tech International Design and
Manufacturing Ltd.
B-Tech AV Mounts and the B-Tech logo are registered trademarks.
All other brands and product names are trademarks of their respective owners.
Photographs are for illustrative purposes only. E&OE.
AMA-BT7004-V1-0221-BTECH MADE IN VIETNAMhttp://btechavmounts.com/bt7004
For More Information Visit
www.btechavmounts.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>