B TECH BT7873 Logitech Rally Range Mounting Plate Installation Guide

BT7873 Logitech Rally Range Mounting Plate
Installation Guide ****

BT7873 Logitech Rally Range Mounting Plate

BT7873
MOUNTING PLATE FOR LOGITECH RALLY RANGE
INSTALLATION GUIDE

SPECIFICATIONS

• Designed to mount a Logitech Rally Bar or Logitech Rally Bar Mini to a variety of B-Tech products
• Ideal for use on a B-Tech display trolley or stand
• Attaches directly to a B-Tech column (878380/8T8381/ 678385), a mounting adaptor arm (878390-SA/8T703)) or to a pole using B-Tech accessory collars (877052/817847)
• Slide to position up/down on the column/poles
  www.btechaymounts.com

INSTALLATION SAFETY INSTRUCTIONS

CAUTION: This mount is intended for use only with the maximum weights indicated. Use with equipment heavier than the maximum indicated may result in instability causing possible injury. Do not attempt to Install this product until all instructions and warnings have been read and properly understood. Please keep these instructions for future reference. Please check carefully to make sure there are no missing or defective parts- defective parts must never be used. 8-Tech AV Mounts, Its distributors and dealers are not liable or responsible for damage or Injury caused by Improper installation, improper use or failure to observe these safety instructions. In such cases, all guarantees will expire.

General

B-Tech AV Mounts recommends that a professional AV installer or other suitably qualified person install this product. Great care must always be taken during installation as most AV equipment Is of a fragile nature, possibly heavy and easily damaged if dropped. If you do not fully understand the instructions or are not sure how to install this product safely, then please consult a professional for advice and/or to install this product for you. Failure to mount this product correctly may cause serious injury or death both during installation and at any time thereafter. Do not mount any AV equipment that exceeds the specific weight limit of the product you are installing. This weight limit will be clearly stated on each product and its packaging and will vary from product to product.
Product location
Please pay careful attention to where this product is located. Check load capacity of the structure prior to Installation as some surfaces are not suitable for installation. Designed for indoor use, this mount is suitable for public or home installation If located in a public or frequently populated area ensure that the product is out of the immediate reach of people. If any AV equipment Is to be suspended over the likely path or location of people then great care should be taken to secure all parts of the installation from falling. When drilling holes it is essential to avoid contact with electrical cables and water or gas pipes contained within. Use of a good quality live wire detector and hidden object locator is therefore recommended. Only drill into structures when you are sure it is safe to do so.
Fixing hardware
It is highly recommended that all fixing screws be used where supplied and that the purpose of all other fixing hardware is fully understood. In some cases more AV equipment fixing hardware will be supplied to accommodate different models of equipment and set up configurations. The installer must be satisfied that any supplied fixing hardware is suitable for each specific installation. The fixing kit supplied with the product may not be suitable for all walls. If any fixing screws or included hardware are deemed not sufficient for a safe installation then please consult a professional or your local hardware store.
Hazard limitation
When routing cables take advantage of any built In cable management features that the product might provide and ensure that all cables are tidy and secure. Check to see that any moving aspect of the product can do so unhindered by any cabling. Some products have moving parts and the potential to cause injury through the crushing or trapping of fingers or other body parts. Particular attention to the nature of moving parts is required especially when assembling installing and adjusting during set up. Immediately after installation double- check that the work done is safe and secure. Double-check all necessary fixings are present and are of ample tightness.
It is recommended that periodic inspections of the product and its fixing points are made as frequently as possible (no more than 6 months apart) to ensure that safety is maintained.
If in doubt consult a professional AV installer or other suitably qualified person.

BT7873 PARTS LIST

PLEASE KEEP THIS FOR FUTURE REFERENCE

Suitable for loads up to 8kg (181bs)

INSTALLATION INSTRUCTIONS

1. ATTACH THE MOUNTING PLATE TO A B-TECH MOUNT
A. RAIL MOUNTING
Fix item 1 to a 878390-SA / 877031 Mounting Adaptor Arm using item 7.

B. POLE MOUNTING
Use an Accessory Collar (877052/8T7847) to mount item 1 onto a 050mm Pole (81-7850/81-4116/8T4178) using item 7.
C. TWIN POLE MOUNTING
Fixing onto double poles – 2 x Accessory Collars (8T7052/8T7841) required.
D. SINGLE COLUMN MOUNTING (BT8380 / BT8381)
Insert 2 x item 8 into the front channels of the column (BT8380 / BT8381) and fix item 1 to the column using item 7.
E. DOUBLE COLUMN MOUNTING (878380 / BT8381)
Insert item 8 into the outside channels of the columns and use items 7 to fix item 1 to the column.
F. Fixing to a single BT8385 column
Insert 2 x item 6 into the front channel on the column and use items 5 to fix item 1 to item 6.
G. Fix onto double BT8385 columns
Insert item 6 into the outside channels of the columns and use item 5 to fix item 1 to item 6.

CONNECT VIDEO BAR TO MOUNTING PLATE

Fix the Logitech Rally Bar to item 1 using items 2, 3 & 4.
BT7873 DIMENSIONS 1
REASE KM 1116103 FUTURE FUIRPICE

THESE INSTRUCTIONS ARE INTENDED AS A GUIDE ONLY AND B-TECH ACCEPTS NO LIABILITY FOR THE ACCURACY OF THE INFORMATION CONTAINED IN THIS DOCUMENT.
CONTACT: info@btechavmounts.com
©2022 B-Tech International Design and Manufacturing Ltd. All rights reserved. B-Tech AV Mounts is a division of B-Tech International Design and Manufacturing Ltd. B-Tech AV Mounts and the B-Tech logo are registered trade marks. All other brands and product names are trademarks of their respective owners. Photographs are for illustrative purposes only. E&OE.

https://www.btechavmounts.com/bt7873
AMA-BT7873-V1-PROBX-0522-57
MADE IN THE UK
For More Information Visit www.btechavmounts.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>