B-TECH BT9340-Rm DVLED Videowall Wall Mount Installation Guide
- June 4, 2024
- B-TECH
Table of Contents
BT9340-Rm
DVD Videowall WALL MOUNT
for rear-mounted deviled cabinets
INSTALLATION GUIDE
B-TECH AV mounts
SPECIFICATIONS
- Designed for rear-mounted DVLED cabinets
- Open frame allows panel access for easy servicing and maintenance
- Pre-assembly of major parts for quick and easy installation
- All mounting hardware included
- For indoor use only www.btechavmounts.com
INSTALLATION & OPERATING SAFETY INSTRUCTIONS
CAUTION:
This mount is intended for use only with the maximum weights indicated. Use
with equipment heavier than the maximum indicated may result in instability
causing possible injury.
Do not attempt to install this product until all installation / operating
instructions and warnings have been read and properly understood. Please keep
these instructions safe for future reference. Please check carefully to make
sure there are no missing or defective parts – defective parts must never be
used. B-Tech AV Mounts, its distributors, and dealers are not liable or
responsible for damage or injury caused by improper installation, improper use
or failure to observe these safety instructions. In such cases, all guarantees
will expire.
General
B-Tech AV Mounts recommends that a professional AV installer or other suitably
qualified person install this product. Great care must always be taken during
installation as most AV equipment is of a fragile nature, possibly heavy and
easily damaged if dropped. If you do not fully understand the instructions or
are not sure how to install this product safely, then please consult a
professional for advice and/or to install this product for you. Failure to
mount this product correctly may cause serious injury or death both during
installation and at any time thereafter. Do not mount any AV equipment that
exceeds the specified weight limit of the product you are installing. This
weight limit will be clearly stated on each product and its packaging and will
vary from product to product.
Product location
Please pay careful attention to where this product is located. Check the load
capacity of the wall prior to installation to ensure that it can support the
combined weight of the equipment and hardware, some surfaces are not suitable
for installation. Warning! Secure to a solid fixture, stability can be
impaired if attached to any unsecured surface or furniture. Designed for
indoor use, this mount is suitable for public or home installation. If located
in a public or frequently populated area ensure that the product is out of the
immediate reach of people. f any AV equipment is to be suspended over the
likely path or location of people then great care should be taken to secure
all parts of the installation from falling. When drilling holes it is
essential to avoid contact with electrical cables and water or gas pipes
contained within. Use of good quality live wire detector and hidden object
locator is therefore recommended. Only drill into structures when you are sure
it is safe to do so.
Fixing hardware
It is highly recommended that all fixing screws be used where supplied and
that the purpose of all other fixing hardware is fully understood. In some
cases more AV equipment fixing hardware will be supplied to accommodate
different models of equipment and set up configurations. The installer must be
satisfied that any supplied fixing hardware is suitable for each specific
installation. The fixing kit supplied with the product may not be suitable for
all walls. If any fixing screws or included hardware are deemed not sufficient
for a safe installation then please consult a professional or your local
hardware store.
Hazard limitation
When routing cables take advantage of any built-in cable management features
that the product might provide and ensure that all cables are tidy and secure.
Check to see that any moving aspect of the product can do so unhindered by any
cabling. Some products have moving parts and the potential to cause injury
through the crushing or trapping of fingers or other body parts. Particular
attention to the nature of moving parts is required especially when assembling
installing and adjusting during set up. Immediately after installation double-
check that the work done is safe and secure. Double-check that all necessary
fixings are present and are of ample tightness.
Operating & Maintenance
It is recommended that periodic inspections of the product and its fixing
points are made as frequently as possible (no more than 6 months apart) to
ensure that safety is maintained. B-Tech AV Mounts recommends that a suitably
qualified person is used for the removal of this product. Please dispose of
the product carefully and with consideration to the environment. If in doubt
consult a professional AV installer or another suitably qualified person.
BT9340-rm PARTS LIST
PLEASE KEEP THIS FOR FUTURE REFERENCE
Note: Images for reference only as sizes, parts and assembly may differ depending on installation type.
|
---|---
If required. (For installing into brick/concrete walls)| Cabinet Fixing Screws/Bobbins Note: May be supplied with DVD cabinet
ITEM| PART NAME
---|---
WALL MOUNT ASSEMBLY
Al| ADJUSTABLE WALL PLATE (BT8390-WFKS)
A2| M8 x 50mm COACH SCREW
A3| No.10 WALL PLUG
RAIL ASSEMBLY
B1| MOUNTING RAIL*
B2| RAIL END CAP
B3| EXTENSION BARS
INTERFACE ASSEMBLY
Cl| INTERFACE PLATE
C2| SPACERS (VARIOUS LENGTHS)
C3| CABINET FIXING SCREW/BOBBIN
TECHNICAL GUIDES
D1| INSTALLATION DRAWING
*Note: Mounting rails (item B1) may be supplied in various lengths
OPTIONAL INTERFACE PLATE EXTENSION KIT
| ITEM | PART NAME |
|---|---|
| C4 | CONNECTOR |
| C5 | M8 x 8mm CSK HEX SCREW |
| C6 | M8 x 8mm BUTTON HEAD HEX SCREW |
ALTERNATIVE WALL PLATE
BT8390-WFK1
| ITEM | PART NAME |
|---|---|
| A1 | FIXED WALL PLATE |
| A2 | ST8 x 45mm CSK WOOD SCREW |
| A3 | No.10 WALL PLUG |
| A4 | M8 INSERT NUT |
| A5 | M8 x 12mm CSK HEX SCREW |
Hex Keys (Assorted)
Installation Drawing
OPTIONAL EXTEND MOUNTING RAILS
Connect item B1* together using item B3 and tighten grub screws, combining the
rails securely.
Repeat this procedure for all rails.
FIX MOUNTING RAILS TO THE WALL
Keyhole mounting – Using a BT8390-WFK5 Adjustable Depth Wall Plate
i. Use the installation drawing (item D1) to mark and drill the fixing holes
for each item A1 assembled on item B1, starting with the bottom rail.
ii. Insert item A2 into the top fixing holes, do not fully tighten.
Allow a gap (approx.10mm) to hook on item A1.
iv. Refer to the installation drawing (item D1) to position and fix the
remaining rails (item B1).
HOOK INTERFACE ARMS ONTO MOUNTING RAILS
i. Hook items C1 onto items B1.
ii. Use the spacers (items C2) to position apart items C1 on the rails*.
iii. Semi-fix items C1 on items B1 by tightening the safety screws on the
bottom hook arms.
Do not fully tighten until DVLED cabinets have been mounted.
OPTIONAL EXTENDING THE HEIGHT OF THE INTERFACE PLATES
Connect items C1 together using the connectors (item C4) with items C5 & C6 as
shown below.
Note: Ensure the interface plates sit flush on top of each other.
MOUNT DVLED CABINETS ONTO INTERFACE ARMS
i. Insert the cabinet fixings or the supplied B-Tech screws/bobbins (item C3)
into the rear of the DVLED cabinets. Leave at least a 6mm gap so the cabinet
can be hooked onto item C1.
ii. Using the keyhole fixings, hook the first cabinet onto the bottom center
item C1 and secure it by tightening items C3 on the rear.
iii. Hook the remaining cabinets onto the mount.
Note: Cabinets may have to be assembled in columns rather than in rows, as
shown below.
Refer to the DVLED cabinet manufacturer’s manual on how to fix the cabinets
together and how to connect the power/data cables.
iv. Once the first row of cabinets has been mounted, use the height adjustment
screws on top of item C1 hooks to level the row. Turn the screw clockwise to
raise item C1.
v. Tighten item C3 on the rear of the cabinets.
ALIGN & SECURE THE CABINETS
i. Optional. If necessary use the height adjustment screws on top of item C1
hooks to level the cabinets.
BT9340-rm DIMENSIONS
PLEASE KEEP THIS FOR FUTURE REFERENCE
CONTACT:
info@btechavmounts.com
©2021 B-Tech International Design and Manufacturing Ltd. All rights reserved.
B-Tech AV Mounts is a division of B-Tech International Design and
Manufacturing Ltd.
B-Tech AV Mounts and the B-Tech logo are registered trademarks.
All other brands and product names are trademarks of their respective owners.
Photographs are for illustrative purposes only. E&OE.
AMA-BT9340-RM-V1-0921-BTECH MADE IN THE UK
https://www.btechavmounts.com/bt9340
For More Information Visit
www.btechavmounts.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>