B-TECH AV MOUNTS BT8237 Flat Screen Articulating Wall Mount Installation Guide
- June 4, 2024
- B-TECH AV MOUNTS
Table of Contents
B-TECH AV MOUNTS BT8237 Flat Screen Articulating Wall Mount
SPECIFICATIONS
- Recommended for screens up to: 75″ (178cm)
- Max load: 80kg (176lbs)
- Universal mount suitable for screens with VESA fixings from 200 x 100 to 600 x 400mm
- Extends from wall: 72.5mm -700mm (3″- 27.5″)
- Features 120° swivel
- Includes coverplates and cable management for a neat and tidy installation
- Simple ‘hook-on’ installation with all mounting hardware included
INSTALLATION SAFETY INSTRUCTIONS
Do not attempt to install this product until all instructions and warnings have been read and properly understood. Please keep these instructions for future reference. Please check carefully to make sure there are no missing or defective parts-defective parts must never be used. B-Tech AV Mounts, its distributors and dealers are not liable or responsible for damage or injury caused by improper installation, improper use or failure to observe these safety instructions. In such cases, all guarantees will expire.
General
B-Tech AV Mounts recommends that a professional AV installer or other
suitably qualified person install this product. Great care must always be
taken during installation as most AV equipment is of a fragile nature,
possibly heavy and easily damaged if dropped. If you do not fully understand
the instructions or are not sure how to instal this product safely, then
please consult a professional for advice and/or to install this product for
you. Failure to mount this product correctly may cause serious injury or death
both during installation and at any time thereafter. Do not mount any AV
equipment that exceeds the speciic weight limit of the product you are
installing. This weight limit will be clearly stated on each product and its
packaging and will vary from product to product.
Product location
Please pay careful attention to where this product is located. Check load
capacity of the wall prior to installation as some surfaces are not suitable
for installation. Designed for indoor use, this mount is suitable for public
or home installation. If located in a public or frequently populated area
ensure that the product is out of the immediate reach of people. If any AV
equipment is to be suspended over the likely path or location of people then
great care should be taken to secure all parts of the installation from
falling. When drilling holes it is essential to avoid contact with electrical
cables and water or gas pipes contained within. Use of a good quality live
wire detector and hidden object locator is therefore recommended. Only drill
into structures when you are sure it is safe to do so.
Fixing hardware
It is highly recommended that al fixing screws be used where supplied and that
the purpose of all other fixing hardware is fully understood. In some cases
more AV equipment fixing hardware will be supplied to accommodate different
models of equipment and set up confgurations. The installer must be satisfied
that any supplied fixing hardware is suitable for each specific installation.
The fixing kit supplied with the product may not be suitable for all walls. f
any fixing screws or included hardware are deemed not sufficient for a safe
installation then please consult a professional or your local hardware store.
Hazard limitation
When routing cables take advantage of any built in cable management features
that the product might provide and ensure that all cables are tidy and secure.
Check to see that any moving aspect of the product can do so unhindered by any
cabling. Some products have moving parts and the potential to cause injury
through the crushing or trapping of fingers or other body parts. Particular
attention to the nature of moving parts is required especially when assembling
installing and adjusting during set up. Immediately after installation double-
check that the work done is safe and secure. Double-check all necessary
fixings are present and are of ample tightness.It is recommended that periodic
inspections of the product and its fixing points are made as frequently as
possible (no more than 6 months apart) to ensure that safety is maintained. If
in doubt consult a professional AV installer or another suitably qualified
person.
PARTS LIST
INSTALLATION INSTRUCTIONS
FIX WALL PLATE
CONCRETE/ BRICK WALL
- Mark and drill 6 fixing holes in the wall.
- Insert item A3 into the holes and 1x item A1 into the top central hole, leaving a gap of approx. 10-15mm so item 1 can easily be hooked on.
- Hook item 1 onto item A1 and fix the remaining 5x item A1 & A2, securing item 1 to the wall.
STUD WALL MOUNTING
- Mark and drill 4x fixing holes on the wooden/stud wall.
- Fix item 1 to the stud wall using items A1 &A2.
ATTACH INTERFACE ARMS TO SCREEN
Fix items 2&3 to the rear of the screen using items A – M.
Note: Ensure the arms are facing the correct way round and the same holes
are used on both arms.
MOUNT SCREEN ONTO INTERFACE PLATE
Using item 2 hook screen onto item 1
Note: This may require two people.
OPTIONAL HEIGHT ADJUSTMENT
To level the screen, use item 7 to tighten the height adjustment screw on top
of item 2 or item 3.
ADD SECURITY SCREWS
To secure screen to mount, insert items 3 &4 into the bottom of the interface
plate underneath the interface arms, securing item 2 to item 1.
CABLE MANAGEMENT
Connect items 5&6 onto item 1.
DIMENSIONS
FRONT VIEW
BACK VIEW
TOP VIEW
SIDE VIEW
Documents / Resources
|
B-TECH AV MOUNTS BT8237 Flat Screen Articulating Wall
Mount
[pdf] Installation Guide
BT8237, Flat Screen Articulating Wall Mount, BT8237 Flat Screen Articulating
Wall Mount
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>