RAB Lighting HIDFA-XXS-EX39-8CCT-BYP-5SP RAB LED Corn Cob Instructions

Lighting HIDFA-XXS-EX39-8CCT-BYP-5SP
RAB LED Corn Cob Instructions

HIDFA-XXS-EX39-8CCT-BYP-5SP RAB LED Corn Cob

HIDFA-XXS-E26-8CCT-BYP/SSP
HIDFA-XXXS-EX39-8CCT-BYP/SSP
Our optional sensors include MW-S/SMW-S, PIR-S/SPIR-S, DAYLIGHT-S, CONTROL/W/AUX/SSP/LCB, CONTROL/W/AUX/SSP/LCBS and CONTROL/W/AUX/SSP/LCBS/MVS. The lamps will perform a s normal if no sensor is inserted. If the lamps use CONTROL/W/AUX/5S5P/LCB, CONTROL/AW/AUX/SSP/LCBS and CONTROL/W/AUX/SSP/LCBS/MVS, please refer to sensor instruction t o get setup and installation guide.
Please note that RAB lamps can’t operate with other brand sensors.

IMPORTANT

READ CAREFULLY BEFORE INSTALLING LED HID BULBS. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
RAB LED HID Bulbs must be wired in accordance with the National Electrical Code and all applicable codes. Proper grounding is required for safety. THIS PRODUCT  MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND  OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.

WARNINGS:

• Main applications include for use in post top, street lights and other suitable light fixtures.
• Operating temperature: -30°C to 60°C (-22°F to 140°F).
• These LED Lamps require all ballasts, capacitors, and ignitors to be bypassed or removed. Do not operate lamps on existing ballasts.
• Dimmable with optional control modules.
• Donotuse with standard dimmers. Only use the control provided with or specified by these instructions to control this lamp. This lamp will not operate properly when  connected to a standard (incandescent) dimmer or dimming control.
• This device is not intended for use with emergency exits.
• Can be used in enclosed fixtures. Do not install 120W in horizontal applications.
• Before installation make certain the AC power to the fixture is off.
• Risk of fire or electric shock. Luminaire wiring and electrical parts may be damaged when drilling for installation of LED retrofit kit. Check for enclosed wiring and  components.
• Risk of fire or electric shock. LED Retrofit lamp installation requires knowledge of luminaires electrical systems. If not qualified, do not attempt installation. Contact a  qualified electrician.
• Donot make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
• Installers should not disconnect existing wires from lampholder terminals to make new connections at lampholder terminals. Instead installers should cut existing  lampholder leads away from the lampholder and make new electrical connections to lampholder lead wires by employing applicable connectors.
• To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
• Risk of fire or electric shock. Install this kit only in luminaires that have the construction features and dimensions shown in the photographs or drawings and where the  input rating of the retrofit kit does not exceed the input rating of the luminaire.
• Use only with a portable luminaire that is provided with a shade.
• Added weight of the device may cause instability of a free-standing portable luminaire.
• Text or diagram showing how the supply connections are made to the lampholders.
• Risk of fire or electric shock. Install this kit only in luminaires that have the construction features and dimensions shown in the photographs and/or drawings and where  the input rating of the retrofit kit does not exceed the input rating of the luminaire.
• RISK OF FIRE OR ELECTRIC SHOCK. LUMINAIRES WIRING, POWER SUPPLY, OR OTHER ELECTRICAL PARTS MAY BE DAMAGED WHEN  DRILLING FOR INSTALLATION OF RETROFIT KIT HARDWARE. INSPECT WIRING AND COMPONENTS FOR DAMAGE.
• THE RETROFIT KIT IS ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY OF THE COMBINATION SHALL BE  DETERMINED BY AUTHORITIES HAVING JURISDICTION. PRODUCT MUST BE INSTALLED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE  WITH THE APPLICABLE AND APPROPRIATE ELECTRICAL CODES. THE INSTALLATION GUIDE DOES NOT SUPERSEDE LOCAL OR NATIONAL  REGULATIONS FOR ELECTRICAL INSTALLATIONS.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide  reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and  used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur ina  particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the  user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet ona circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

LAMP INSTALLATION

1. Turn off the power before installation.
   Remove old ballast or disconnect from existing lamp holder. Shown as Figure 1.
   Remove and dispose of ballast in correct manner. (North America 100-277VAC)

2. Reconnect directly to the existing lamp holder. Shown as Figure 2.
   (North America 100-277VAC)

3. Select power and color temperature (CCT) of new LED replacement lamp before in stallation.

4. Install new LED replacement lamp. Shown a s Figure 3, Please make sure the old fitting is correctly grounded.
   Attach retrofit label to luminaire. (North America 100-277VAC)

Securely fasten the ground wire to the main body structure, If the wire is damaged in any way please replace.
(Do not use existing burnt out wire). If needed, the replacement ground wire must be 1.0mm in size and insulated from heat.

SELECTABLITY

Power and CCT Selectable

Note: These instructions do not cover aid details or variations in equipment nor do they provide for every possible situation during installation, operation or maintenance.

SAFETY CABLE INSTALLATION INSTRUCTION

AS You must use the safety cable to secure the lamps equal tour over 80W in case of falling down due to old socket.

1. Remove the enclosed safety cable from the package.
2. Attach the safety cable to one end of the lamp.
3. Attach the other end of the safety cable to the luminaire.

© 2022 RAB LIGHTING Inc.
Cranbury, New Jersey 08512 USA
HIDFAPTSSP-IN-1122
Easy Answers
rablighting.com
Visit our website for product info
Tech Help Line
Call our experts: 888 722-1000
e-mail Answered promptly-sales@rablighting.com
Free Lighting Layouts
Answered online or by request

Documents / Resources

| RAB Lighting HIDFA-XXS-EX39-8CCT-BYP-5SP RAB LED Corn Cob [pdf] Instructions
HIDFA-XXS-EX39-8CCT-BYP-5SP RAB LED Corn Cob, HIDFA-XXS-EX39-8CCT-BYP-5SP, RAB LED Corn Cob, LED Corn Cob, Corn Cob
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>