SIGMA ROX 12.1 EVO GPS Bike Computer User Guide
- June 9, 2024
- SIGMA
Table of Contents
SIGMA ROX 12.1 EVO GPS Bike Computer
Product Information
The SP2 GPS Bike Computer is a device designed for cyclists to track their speed, cadence, heart rate and other important cycling metrics. The device comes with a sensor set for installation, a USB-C cable for charging and data transfer, and an instruction manual.
Technical Information
- Battery type: not specified
- Maximum operating altitude: not specified
- Operation temperature: not specified
Button Functions
| Button | Function |
|---|---|
| HOME/POWER | Turns the device on/off and returns to the home screen |
| START/ENTER | Starts or enters a selection |
| STOP/BACK | Stops or goes back to the previous screen |
Charging and Data Transfer
- Open the USB cover.
- Insert the USB-C cable. Make sure the cable and port are dry!
- Charge with 5V max. 1400mA.
- Connect to a PC for data transfer.
- Make sure to close the USB cover before starting a training session.
Installation – Speed/Cadence Sensor
- Remove the sticker from the sensor.
- Mount the sensor on the bicycle hub of both wheels.
- Watch the video tutorial for more information at goto.sigmasport.com/rox12-1-tutorials.
- The blue light flashes when properly installed.
Heart Rate Sensor Battery Change
- Open the sensor cover.
- Replace the battery with a new CR2032 battery.
- Make sure to close the sensor cover.
For more detailed instructions, please refer to the complete manual available at goto.sigmasport.com/rox12-1.
This manual is a quick guide. You can access the detailed instructions by
following this link:
goto.sigmasport.com/rox12-1
CONTENTS
INSTALLATION
HEART RATE SENSOR
HEART RATE SENSOR BATTERY CHANGE
SPEED
/ CADENCE SENSOR FIRST START
SPEED SENSOR
The SPEED sensor can be mountedon the bicycle hub of both wheels
CADENCE SENSOR
BUTTON FUNCTIONS
- HOME/POWER Button
1. Switch on/off the device (press for 3s)
2. Training: Power Save Mode (press for 3s)
3. Back to Home Screen- START/ENTER Button
1. Start/Continue training
2. Take manual lap in training
3. Workout: Start next Workout Phase- STOP/BACK Button
1. Stop training- Button
- Zoom In on Map
- Swipe right
- Button
- Zoom Out on Map
- Swipe left
CHARGING AND DATA TRANSFER
- Open USB Cover.
- Insert USB-C cable. Check that the cable and port are dry!
- Charge with 5V max. 1400mA.
- Connect to PC for data transfer.
NOTE:
To get to optimum charging time, a charger with min. 1500mA should be used.
Please make sure, that you don‘t use a charger that exceed the max. of 3000mA,
as it could damage the device.
IMPORTANT: Please ensure that the USB cover is always closed before
starting a training session.
TECHNICAL INFORMATION
ROX 12.1 EVO
- Battery type Rechargeable 2400 mAh /9.12 Wh Battery
- Maximum operating altitude 5000 m
- Operation temperature 0 °C to 40 °C
- Operation frequency
- WiFi 2.4 GHz @ 15.1 dBm nominal
- ANT+ 2.4 GHz @ 4 dBm nominal
- Bluetooth 2.4 GHz @ 4 dBm nominal
- GPS 1575.42 MHz (receiver only)
- GLONASS 1602 MHz (receiver only)
- Galileo 1575.42 MHz (receiver only)
- Transmission power <20 dBm
- Water and Dust rating IP67
You can find the CE declaration at: ce.sigmasport.com/rox121
FCC
Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation of the device.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Radiation Exposure Statement:
The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available.
Industry Canada statement
This device complies with ISED’s licence-exempt RSSs. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation of the device.
Do not disassemble, modify or repair this product, as this may cause a fire,
electric shock or product damage. Any modification will void the warranty of
this product.
This Class B digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3
(B).
Radiation Exposure Statement:
The product comply with the Canada portable RF exposure limit set forth for an
uncontrolled environment and are safe for intended operation as described in
this manual. The further RF exposure reduction can be achieved if the product
can be kept as far as possible from the user body or set the device to lower
output power if such function is available.
SIGMA-ELEKTRO GmbH
Dr.-Julius-Leber-Straße 15 67433 Neustadt/Weinstraße Germany
kundenservice@sigmasport.com
FCC ID : M5LROX-12-1 IC: 7580A-ROX121 Contains
FCC ID : QOQWFM200 Contains IC ID: 5123A-WFM200
www.sigmasport.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>