MPOW BH475A Wireless Headphones for TV User Manual
- June 6, 2024
- MPow
Table of Contents
MPOW BH475A Wireless Headphones for TV
PACKING LIST
HOW TO CHARGE
TRANSMETA DIAGRAM
- BT power switch
- BT indicator light
- Optical port
- Optical indicator
- Optical or AUX/DCIN switch
- AUX/DCIN indicator light
- AUX port (3.5mm audio port)
- DCIN port (USS port)
- A/B button
- Power indicator light
USE ENVIRONMENT
Turn the BT Power Switch to “ON” to power on the transmitter. Then. the transmitter will enter Bluetooth transmitter mode. In this way, the audio files from Non-Bluetooth audio sources will be transmitted to a Bluetooth headset/ Bluetooth speaker, etc. via Bluetooth transmission.
HOW TO CONNECT
TRANSMITTER CONNECT WITH NONBLUETOOTH DEVICE
- Connect to a computer****
Connect the transmitter to your computer with the data cable and turn on the BT Power switch of the transmitter. Flip the Optical or AUX/ DCIN switch to the AUX side. For the first use. the computer will automatically prompt that the driver has been installed successfully. After the installation, the transmitter will begin to serve.
- Connect to a TV through AUX
- Connect the transmitter to the USB port of the television with the data cable. Or connect the transmitter to a SV DC power supply with the data cable.
- Connect the AUX port of the transmitter to the AUX port of the television with an AUX cable.
- Flip the Optical or AUX/ DCIN switch to the AUX side.
- Connect to a TV through OPTICAL
- Connect the transmitter to the USB port of the television with the data cable. Or connect the transmitter to a SV DC power supply with the data cable.
- Connect the Optical port of the transmittertotheOptical port of the television with an Optical cable.
- Flip the Optical or AUX/ DCIN switch to the Optical side.
- ConnecttoaTVthrough RCA
- Connect the transmitter to the USB port of the television with the data cable. Or connect the transmitter to a 5V DC power supply with the data cable.
- Connect the AUX port of the transmitter to the RCA port of the television with a 3.5mm male to 2 RCA male cable.
- Rip the Optical or AUX/DCIN switch to the AUX side.
TRANSMITTER PAIR WITH BLUETOOTH HEADPHONE
Enable the Bluetooth function on your Bluetooth device (such as Bluetooth headset/ Bluetooth speaker). Place it about 3.3ft (l m) within the transmitter. When pairing is completed, the blue indicator light stays on for l Omin and then goes off.
DISCONNECT FROM THE CURRENT BLUETOOTH DEVICE
CLEAR THE PAI RI NC RECORD
DUAL CONNECTION
- PressA/B button once with the BT indicator flash blue quickly.
- Enable the Bluetooth function on your first Bluetooth device, and connect with the transmitter.
- Press A/B button once again with the BT indicator flash blue quickly.
- Enable the Bluetooth function on your second Bluetooth device, and connect with the transmitter.
HEADPHONE DIAGRAM
HOW TO PAIR
With your headphones powered off, press and hold the MFB until the red and blue lights flash alternately to enter the pairing mode. Enable the Bluetooth feature of your cellphone and find “MPOWT20” to connect.
PLAV/PAUSE/ANSWER/HANC UP/ REJECT/REDIAL
VOLUME CONTROL/MUSIC CONTROL
FCC
Any changes or modifications not expressly approved by the party responsible
for compliance could void the users authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference. and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Charging box Radiation Exposure Statement:
This equipment should be installed and operated with a minimum distance of
20cm between the radiator & your body.