SIGMA BUSTER 1100 Lumens Front Light Instruction Manual

: June 2, 2024
: SIGMA

Table of Contents

SIGMA BUSTER 1100 Lumens Front Light
CE INFORMATION
MOUNTING
3D RUBBER PAD ADJUSTMENT
MODE MEMORY FUNCTION
PRESET MODE PROFILES
BATTERY INDICATOR
CHARGING
CHARGING INDICATOR
TECHNICAL DATA
FCC DECLARATION OF CONFORMITY
ACCESSORIES
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SIGMA BUSTER 1100 Lumens Front Light

SIGMA-BUSTER-1100-Lumens-Front-Light-product

CE INFORMATION

SIGMA-ELEKTRO GmbH hereby declares that the BUSTER 1100 comply with the fundamental requirements and other relevant regulations of Directive 2014/30/EU and RoHS Directive 2011/65/EU. You can fi nd the CE declaration at: ce.sigmasport.com/buster1100

WARNING

Possibly dangerous optical radiation! Never look directly into the lamp or point it at other people‘s eyes while it is in operation.

MOUNTING

SCREW-BRACKET MOUNT

Adjust the BUSTER 1100 so that it does not blind other road users. The BUSTER 1100 must be securely attached to the bike and light distribution must not be obstructed. SIGMA-BUSTER-1100-Lumens-Front-Light-fig-14

3D RUBBER PAD ADJUSTMENT

SIGMA-BUSTER-1100-Lumens-Front-Light-fig-16

VIDEO TUTORIALS
Detailed tutorials and application tips can be found at this link.

goto.sigmasport.com

SIGMA-BUSTER-1100-Lumens-Front-Light-fig-2

6 MODES

SIGMA-BUSTER-1100-Lumens-Front-Light-fig-1

THERMAL PROTECTION CIRCUIT:
The lamp is suffi ciently cooled while riding. If the temperature of the lamp rises above 60 °C, it automatically switches to the next weaker mode.

MODE MEMORY FUNCTION

SIGMA-BUSTER-1100-Lumens-Front-Light-fig-3

EXAMPLE

PRESET MODE PROFILES

PROFILE SELECTION:
You can adapt your BUSTER 1100 individually to your requirements. For this purpose, the lamp has 5 different profi les that you can select as follows. Hold down the ON/OFF button for longer than 5 seconds when it is switched off, then you will get to the profi le selection. The lamp fl ashes once for profi le 1, twice for profi le 2 and so on. To select the desired profi le, press the ON/OFF button once. Your selection is confi rmed by four short fl ashes of the front LED. SIGMA-BUSTER-1100-Lumens-Front-Light-
fig-5

BATTERY INDICATOR

NOTE: If the battery capacity is less than 20 %, the red indicator LED lights up and after about 45 minutes, the red LED begins flashing, and the BUSTER 1100 goes out completely shortly thereafter. SIGMA-BUSTER-1100-Lumens-
Front-Light-fig-6

CHARGING

Charge the lamp only at room temperature. Charging is not possible outside the charging temperature range of +10 °C to +45 °C (50 °F to 110 °F) (recognisable by the rapid flashing of the red indicator LED).
Ensure that the USB sealing marked red is always closed correctly after charging.
No energy can be transferred out through the USB-C connection.

CHARGING INDICATOR

SIGMA-BUSTER-1100-Lumens-Front-Light-fig-8

TECHNICAL DATA

Charging Temperature:
- +10°C to +45°C
- 50 °F and 110 °F
Battery Type:
- 3.7 V, 7000 mAh
Max power:
- 3 W
Water and Dust rating:
- IP44

FCC DECLARATION OF CONFORMITY

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifi cations could void the user’s authority to operate the equipment. This equipment should be installed and operated with a minimum distance of 5 millimeters between the radiator and your body.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

FCC Caution:
Any changes or modifi cations not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

Radiation Exposure Statement:
The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available.