SIGMA BUSTER 400 HL Front Light Headlight Instruction Manual
- June 1, 2024
- SIGMA
Table of Contents
*≤ 120m ≤ 25h USB-C SAFE**
- Basis ANSI Nema FL1
BUSTER 400 FRONTLIGHT HEADLIGHT
CE INFORMATION
SIGMA-ELEKTRO GmbH hereby declares that the BUSTER 400/HL comply with the fundamental requirements and other relevant regulations of Directive 2014/30/EU and RoHS Directive 2011/65/EU. You can fi nd the CE declaration at: ce.sigmasport.com/buster400, ce.sigmasport.com/buster400hl
MOUNTING OPTIONS
HELMET BRACKET
With one velcro strap
Optimal mounting option for helmets with parallel ventilation slots.
With two velcro straps
Alternative mounting option for helmets with ventilation slots shown on the right.
MOUNTING
(1) (2)
The desired position of the bike light can be locked by tightening the screw.
SIGMA TIP:
Tighten the screw so that you can also adjust your bike light without tools
while driving.
VIDEO TUTORIALS
goto.sigmasport.com/busterhelmet/video
DO YOU ALSO KNOW OUR BIKE COMPUTERS?
More SIGMA Bike Computers at sigmasport.com
SILICONE BRACKET
Adjust the BUSTER 400 so that it does not blind other road users. The BUSTER 400 must be securely attached to the bike and light distribution must not be obstructed.
(1) (2) (3)
- 360° adjustable
(4) (5)
ADAPTER FOR ACTION CAMERA BRACKET
VIDEO TUTORIALS
Detailed tutorials and application tips can be found at this link.
goto.sigmasport.com/buster400/service
5 MODES
MODE MEMORY FUNCTION
When the BUSTER 400 is switched off, it will keep the last used mode.
EXAMPLE
-
2 x
short click
ON -
3 x
short click -
1 x
long click
2 sec.
PRESET MODE PROFILES
PROFILE SELECTION:
You can adapt your BUSTER 400 individually to your requirements. For this
purpose, the lamp has 5 different profiles that you can select as follows.
Hold down the ON/OFF button for longer than 5 seconds when it is switched off,
then you will get to the profile selection. The lamp flashes once for profile
1, twice for profile 2 and so on.
To select the desired profile, press the ON/OFF button once. Your selection is
confirmed by four short flashes of the front LED.
-
PROFILE 1
-
PROFILE 2
-
PROFILE 3
-
PROFILE 4
-
PROFILE 5
-
NO CHANGE OF THE PROFIL SET
-
NIGHT FLASHING
DAY FLASHING -
HIGH
NIGHT FLASHING -
HIGH
LOW
DAY FLASHING -
HIGH
MID
LOW -
HIGH
MID
LOW
NIGHT FLASHING
DAY FLASHING -
1 x
long click
5 sec. -
OK
1 x click
Select profile
BATTERY INDICATOR
NOTE: If the battery capacity is less than 20 %, the red indicator LED lights up and after about 45 minutes, the red LED begins flashing, and the BUSTER 400 goes out completely shortly thereafter.
- BATTERY STATUS
In the switched-off state, 1x short click shows the current battery status.
CHARGING
The lamp needs to be charged at room temperature.
(Charging temperature: +10 °C to +45 °C) (50 °F to 110 °F).
Ensure that the USB sealing marked red is always closed correctly after charging.
No energy can be transferred out through the USB-C connection.
Charger not incl.
- Battery rating:
3.7V 2000 mAh
CHARGING INDICATOR
Charging approx. 4 h at 5V 1 A
TECHNICAL DATA
Charging Temperature:
+10°C to +45°C
50 °F and 110 °F
Battery Type:
3.7 V, 2000 mAh
Max power:
3 W
Water and Dust rating:
IP44
FCC DECLARATION OF CONFORMITY
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must
accept any interference received, including interference that may cause
undesired operation. The grantee is not responsible for any changes or
modifications not expressly approved by the party responsible for compliance.
Such modifications could void the user’s authority to operate the equipment.
This equipment should be installed and operated with a minimum distance of 5
millimeters between the radiator and your body.
NOTE:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment.
Radiation Exposure Statement:
The product comply with the FCC portable RF exposure limit set forth for an
uncontrolled environment and are safe for intended operation as described in
this manual. The further RF exposure reduction can be achieved if the product
can be kept as far as possible from the user body or set the device to lower
output power if such function is available.
UKCA STATEMENT
We, SIGMA-ELEKTRO GmbH, declare that the equipment above has been tested in our facility and found compliance with the requirement limits of applicable standards, in accordance with the Electromagnetic Compatibility Regulations 2016 and the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012. The test record, data evaluation and Equipment Under Test (EUT) configurations represented herein are true and accurate under the standards herein specified.
WARNING
Possibly dangerous optical radiation! Never look directly into the lamp or
point it at other people‘s eyes while it is in operation.
It is essential to observe the further safety instructions in the
enclosed sheet, especially regarding the safe use of the lighting.
ACCESSORIES
Please visit sigmasport.com for available accessories
SIGMA-ELEKTRO GmbH
Dr.-Julius-Leber-Straße 15
67433 Neustadt / Weinstraße
Germany
kundenservice@sigmasport.com
Designed in Germany
Manufactured in China
189610/1
189610-1_BUSTER-400+HL_Manual_90x55.indd 23.01.2024 15:04:03
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>