mxion APS 2 Channel Pendulum Control User Manual

June 9, 2024
mXion

mxion - logo APS 2 Channel Pendulum Control
User Manual
mxion APS 2 Channel Pendulum Control

Introduction

Dear customer, we strongly recommend that you read these manuals and the warning notes thoroughly before installing and operating your device. The device is not a toy (15+).
NOTE: Make sure that the outputs are set to appropriate value before hooking up any other device. We can’t be responsible For any damage if this is disregarded.

General information

We recommend studying this manual thoroughly before installing and operating your new device. Place the decoder in a protected location. The unit must not be exposed to moisture.
NOTE: Some functions are only available with the latest firmware. Please make sure that your device is programmed with the latest firmware.

**Summary of Funktions

**

  • DC/AC/DCC operation
  • Digital controllable via decoder (DCC, MM)
  • 5 Amps pendula output
  • Current- and temperature control
  • 3 contact inputs
  • Middle stop function available
  • Poti for stop time
  • Poti for drive time
  • Poti for drive speed
  • Screw drives for stable mounting
  • State LED
  • Drive time between 1 – endless sec.
  • Wait time between 2 sec to 4 min.
  • Slew times configurable with our PC programmer
  • All trains can be pendula control also with decoders
  • Fits to LGB bumper

Scope of supply

Manual mien APA

**Hook-Up

**

Install your device in compliance with the connecting diagrams in this manual. The device is protected against shorts and excessive loads. However, in case of a connection error e.g. a short this safety feature can’t work and the device will be destroyed subsequently.
Make sure that there is no short circuit caused by the mounting screws or metal.

**Connectors

**

Speed: 1-255 steps (255 = max. voltage)
Wait time: 2 sek – 4 min.
Drive time: 1 – 127 sec. If 0 (min) then endless if contact is pressed Middle stop is by 50% if activated.mxion APS 2 Channel Pendulum Control -
Middle stop

Pendula control via time

The driving and stopping times as well as the  speed is about the right sides controller set  (POTI). Alternatively, a red switch to be activated on an intermediate stop half way.mxion APS 2 Channel Pendulum Control - Pendula
control

Pendula control via contact

To do this, set a travel time of 0 (min). From then the APA only „listens“ to the contacts as a limitation. Alternatively, an intermediate stop can be activated, triggered by K3. This does not have to be in the middle, but can be arbitrarily distributed between the two endpoints. Either reed switches can be used as contact like our Art No-0051 or via contact track separation. Note the coasting times! mxion APS 2 Channel Pendulum Control - Pendula control via
contact Pendula control via digital
When connecting a digital voltage to the APA there is the possibility of the delay times set for slow starting and braking. There is also the possibility of using the turnout command switching the control on and off and with it that interrupt or start commuting. Of it is also possible when using our 30Z digital center with model railroad time a small one activate automation. You can do this at certain modest rain times (e.g. 9 am and 12 o’clock off) activate the control. Of the model railway factor can be set at our 30Z.
The further connection corresponds to the previous pictures. In the appendix you will find the CV list for configuration.
The module can handle DCC an Motorola

Product description

The mien analog pendulum automatic (APA) a universally applicable automatic shuttle or any application such as locomotive control cable cars or fair controls. The special thing about ours in addition to the usual control system, APA ist hat not only the waiting time, but also the travel time and even set the speed on the APA can be. That simplifies the structure enormously. In addition to the pure time controlled, it is of course, control via contacts s also possible to be completed. Furthermore a stopover can be made to be activated. Of course, the moves are very gentle started and braked, these times are even adjustable via our PC programmer 0024. With digital control, the APA activated and deactivated via a digital switch command. The train then drives still to the terminus and stops there the pendulum control until it is released.
Further is it possible in digital to use a time control to create a schedule. To do this, our digital command station 30Z is needed.

Thanks to many setting options, the handling is child’s play. It can even do without any wiring can only be oscillated over time. The voltage applied also plays only one role minor role as the speed can be set directly on the pendulum control.
In digital, the LED is activate when deactivated pendulum control. If the LED flashes it is on short circuit before. To do this, the APA must be de- energized be asked.

CV-Table
S = Default, L = Loco address, S = Switch address, LS = Loco and switch address usable

CV Description S L/S Range Note
7 Software version read only (10 = 1.1)
7 Decoder reset functions
2 ranges available 11

16

| basic settings programming lock (CV 15/16)
8| Manufacturer ID| 160| | –| read only
7+8| Register programming mode
Reg8 = CV-Address Reg7 = CV-Value| | | | CV 7/8 don’t changes his real value CV 8 write first with cv-number, then CV 7 write with value or read (e.g.: CV 49 should have 3)  CV 8 = 49, CV 7 = 3 writing
15| Programming lock (key)| 95| S| 0 – 255| to lock only change this value
16| Programming lock (lock)| 95| S| 0 – 255| changes in CV 16 will change CV 15
18| Switch address calculation| 0| S| 0/1| 0 = Switch address like norm

1 = Switch address like Rocco, Fleischmann

20| Switching address high| 0| W| 1 – 2048| Switching address for switching the shuttle mode on / off
21| Switching address low| 1| W
22| Pendulum control active at start| 1| | 0/1| 0 = inactive, 1 = active
23| Pendulum control status| 1| | 0/1| do not change
24| Start-up braking time| 15| | 1 – 255| Time value 1 ms / value
25| Switch-on time hour| 15| | 0 – 23| For automatic operation when using model railway time with our 30Z
26| Switch-on time minute| 0| | 0 – 59
27| Switch-off time hour| 18| | 0 – 23
28| Switch-off time minute| 0| | 0 – 59
29| Time control activation| 0| | 0/1| 0 = inactive, 1 = active
30| Maximum current limit| 40| | 0 – 50| Current limit in decamps (40 = 4A)

Technical data

Power supply: 7-24V DC/DCC 5-18V AC
Current: 20mA (without functions) Maximum function current: 5A
Temperature range: -20 up to 80°C
Dimensions LBH (cm): 6.46.44

NOTE: In case you intend to utilize this device below freezing temperatures, make sure it was stored in a heated environment before operation to prevent the generation of condensed water. During operation is sufficient to prevent condensed water.

Warranty, Service, Support
micron-dynamics warrants this product against defects in materials and workmanship for one year from the original date of purchase. Other countries might have different legal warranty situations. Normal wear and tear, consumer modifications as well as improper use or installation are not covered.
Peripheral component damage is not covered by this warranty. Valid warrants claims will be serviced without charge within the warranty period. For warranty service please return the product to the manufacturer. Return shipping charges are not covered by micron-dynamics. Please include your proof of purchase with the returned good. Please check our website for up to date brochures, product information, documentation and software updates. Software updates you can do with our updater or you can send us the product, we update for you free.
Errors and changes excepted.
EC declaration of conformity
This product meets the requirements of the following EC directives and bears the CE mark for this.
2014/30/EU on electromagnetic compatibility. Underlying standards: EN 55014-1 and EN 61000-6-3. To the electromagnetic compatibility during operation to maintain, follow the instructions in this guide.
EN IEC 63000:2018 to limit the use of certain hazardous substances in electrical and electronic equipment (RoHS).

WEEE Directive
This product meets the requirements of EU Directive 2012/19/EC on electrical and waste electronic equipment (WEEE). Dispose of this product does not have the (unsorted) household waste, but run it the recycling to.
WEEE: DE69511269
Hotline
For technical support and schematics for application examples contact: micron- dynamics info@micron-dynamics.de service @micron-dynamics.de

mxion - logowww.micron-dynamics.de
https://www.youtube.com/@micron-dynamics

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals