ET2 E23514 Nodes 40 Inch LED Pendant CCT Select User Manual
- June 9, 2024
- ET2
Table of Contents
Contemporary
Lighting™
Item/Model Number: E23514
Nodes 40″ LED Pendant CCT Select
Lamping | Ampoule: LED Integrated 50W
Please consult a qualified electrician prior to install
Made in China
LED LOW-VOLTAGE INSTRUCTIONS
Before Getting Started
Read the instructions carefully prior to assembling the product.
When you open the package with a sharp tool like a box knife, be careful not to damage the components inside.
Carefully remove all packaging materials and retain for future use.
Keep all hardware parts and packaging out of reach or small children.
Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the product.
Ensure that you have all required contents for complete assembly.
Take care when lifting. Assemble the product in close proximity to where you intend to install it.
Do not over tighten the screws and bolts as this may damage the threads.
Do not let children play with this product.
Risk of suffocation!
Keep packaging materials away from children.
Lamp Care Instructions
Carefully read through the instruction sheet before assembly and using the product.
Caution there is a risk of shock!
Disconnect from power source before assembling or cleaning.
Switch off, unplug and allow bulb to cool before replacing bulb or cleaning.
Only use the recommended bulb type and do not exceed the maximum wattage as it could cause fire.
Check the product cord to be sure is free torn or frayed.
WARNING: Wires must to be connected to low voltage driver and should not be connected directly to live wire or a short may occur.
Cleaning & Maintenance
On polished finishes, often using talc powder can reduce the appearance of fingerprints and other smudges.
For respective shade surfaces, use the appropriate cleansers, i.e. glass cleaner, stone polish, & wood polish.
Clean with soft cloth and a mild detergent. Do not use abrasive or harsh cleaners.
Periodically (every 90-180 days) make sure that the screws are fully tightened.
Prolonged exposure to heat sources may cause glazing, melting and scorching, or even cause color to fade.
PARTS
Before getting, started, ensure the package contains the following components:
A | x1 | |
---|---|---|
B | x1 | |
C |
5/32-1.26’’
| x2
D| | x3
E|
M4| x2
F|
LED DRIVER
120-277V | 2250mA| 5.12”x1.17”x1.02”
| x1
- Positive Wire
- Ground Screw
- Ground Wire
- Neutral Wire
WIRING DIAGRAM
DIMMER COMPATIBILITY
ITEM/MODEL: E23514
MUST be installed by an experienced professional
CRITICAL KNOWLEDGE of electronic lighting systems required
IMPROPER WIRING and/or INCORRECT DIMMER use can cause C ATASTROPHIC DAMAGE!
THIS FIXTURE MUST BE INSTALLED with a COMPATIBLE DIMMER SWITCH
DO NOT CUT FACTORY-MADE CONNECTIONS.
VOLTAGE INPUT
AC120-277V 60Hz
-
WHITE (N)
-
BLACK (L)
-
PVD4O-C166V24-UNV3-HE-P
-
Black(-)
-
Red(+)
-
Vio (-1-)
-
Pk(-)
-
Black wire (-)
-
Red wire (+)
-
BLACK (L)
-
WHITE (N)
-
LED CV DRIVER 120-277V I 24V I 2250mA
-
Black(-)
-
Red(+)
SCHEMATIC
FOR GENERAL
REFERENCE ONLY
FOR OPTIMAL USE, VERIFIED DIMMERS INCLUDE
Lutron Diva DVCL-153P
Lutron Diva DVELV-300P
DEAKO-Smart Dimmer
DEAKO-Single Dimmer
Lutron Caseta PD-6WCL
Leviton 6672-L
Eaton DALO6P
NOTE:
Triac & ELV dimming is ONLY compatible at 120V
IMPORTANT!
If the control is not paired properly to LED fixtures, irreparable damage may occur.
If the dimmer you are using is not listed here, consult a lighting professional or view our Dimming Compatibility Chart online: www.et2online.com
© 2023 ET2 CONTEMPORARY LIGHTING
Documents / Resources
| ET2
E23514 Nodes 40 Inch LED Pendant CCT
Select
[pdf] User Manual
E23514 Nodes 40 Inch LED Pendant CCT Select, E23514, Nodes 40 Inch LED Pendant
CCT Select, Nodes 40 Inch LED Pendant, LED Pendant, Pendant
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>