Banggood TS-9210 Radio Mirror Projection Clock Instruction Manual

Banggood TS-9210 Radio Mirror Projection Clock

TS-9210 Radio Mirror Projection Clock Manual

The TS-9210 Radio Mirror Projection Clock measures 18.5cm x 2.4cm and includes the following:

• AL1 and AL2 alarm settings
• LED time display with six levels of brightness adjustment
• Snooze function, adjustable between 5 to 60 minutes
• Automatic light-sensitive function
• Projection function that can be rotated 180 degrees
• Radio function with 4-bit time display for hour and minute
• 12-hour and 24-hour format options
• Type-C power cord power supply or CR2032 button battery (sold separately)

Usage Instructions

Power Supply Method

The TS-9210 Radio Mirror Projection Clock can be powered using:

1. Type-C power cord (1.5m USB power cord) power supply. LED lights will always be on when the power cord is connected.
2. CR2032 button battery, which is not included and only used to remember the time.

Power On and Reset

When powered on, the clock will display:

• LED white light
• Time : 0:00
• Default time system : 24-hour format
• Default unit: temperature ;humidity [%]

Time Setting

1. In the time display mode, press the set button to enter the setting mode. The setting items will be displayed and flashing, and the setting sequence is: hour setting, minute setting, 12/24 hour system setting, and snooze hour setting.
2. During the setting process:
   • Short press the up/projection button to increase the value by 1.
   • Long press the up/projection button to quickly increase by 8 steps/s.
   • Short press the down/switch temperature units button to decrease the value by 1.
   • Long press the down/switch temperature units button to quickly decrease by 8 steps/s.
3. If there is no operation within 10 seconds during the setting process, the current setting will be saved automatically and the time setting mode will be exited.
4. In the time display mode,press the【set】to enter the setting mode,the setting items are displayed and flashing,and the setting sequence is: hour setting → minute setting → 12/24 hour system setting → snooze hour setting. (As shown in Figure 1)
5. During setting, short press【▲】to increase the value by 1; long press【▲】to quickly increase (8 steps/s); short press【▼】to decrease the value by 1;long press【▼】to quickly decrease (8 steps/s).
6. If there is no operation within 10 seconds during the setting process, the current setting will be saved automatically and the time setting mode will be exited.

Alarm Setting

1. In the time display mode, press the AL1/AL2 button to enter the alarm clock setting mode. The setting items will be displayed and flashing during the setting process, and the setting sequence is: AL1 hour setting, AL1 minute setting, AL1 alarm mode selection and off alarm setting, AL2 hour setting, AL2 minute setting, AL2 alarm mode selection and off alarm setting.
2. During the setting process:
   • Short press the up/projection button to increase the value by 1.
   • Long press the up/projection button to quickly increase by 8 steps/s.
   • Short press the down/switch temperature units button to decrease the value by 1.
   • Long press the down/switch temperature units button to quickly decrease by 8 steps/s.
3. In the time display mode,press the【al 1.2】 to enter the alarm clock setting mode, and the setting items are displayed and flashing during the setting process. and the setting sequence is:AL1 hour setting → AL1 minute setting → AL1 alarm mode selection and off alarm setting → AL2 hour setting → AL2 minute setting →AL2 alarm mode selection and off alarm setting. (As shown in Figure 2)
4. When setting alarm 1, AL1 icon is displayed, and when setting alarm 2, AL2 icon is displayed.
5. During setting, short press【▲】to increase the value by 1; long press【▲】to quickly increase (8 steps/s); short press【▼】to decrease the value by 1;long press【▼】to quickly decrease (8 steps/s).
6. When setting the alarm mode, the default display is “OFF”, press【▲】/【▼】to switch to display “bu” or “rd”, OFF = turn off the alarm clock, bu = BIBIBI sound, rd =radio sound.

The TS-9210 Radio Mirror Projection Clock is a versatile and easy-to-use product that offers a range of features for your convenience.

Function and button indication diagram

Thank you for purchasing and using the TS-9210 radio mirror projection clock, the following is the user’s operating guide.

Functions

• LED time display
• The default is the brightest , six levels of brightness can be adjusted
• 7 function buttons:
• Projection function, projection can be rotated 180 degrees
• Radio function
• 4-bit time display: hour, minute
• 12-hour format and 24-hour format can be switched, default 24-hour format
• The default display of the clock is 0:00 at power on
• Two sets of alarm clock
• Snooze function, 5 to 60 minutes adjustable
• Automatic light-sensitive function
• Temperature and humidity functions (temperature units can be switched °C/°F)

Power supply method：

1. Type-c power cord power supply (the LED lights always on when the power cord is powered).
2. CR2032 button battery (The battery is not powered and is only used to remember the time).

Note : The product is shipped without batteries

Alarm and snooze

1. The alarm time is 2 minutes.
2. When the alarm sounds, the alarm symbol “AL1″/”AL2” flashing.
3. Snooze function : When AL1 or AL2 alarms, press 【 】to enter the snooze mode, the default is 5 minutes.Press other keys except 【 】to stop the alarm.

Brightness selection and automatic light-sensing

1. Power on the LED display default brightest gear.
2. press the【 】to switch the sequence of brightness:100%-80%-60%-40%-20%-0%→cycle. (As shown in Figure 3)
3. In the time display mode, long press【 】for 2 seconds, “ON” will be displayed to turn on the auto-sensitive function; long press【 】again for 2 seconds,”OFF” will be displayed to turn off the auto-sensitive function.(As shown in Figure 4)
4. Automatic light sensing: the product automatically senses according to the strength of the ambient light and darkness, the brighter the ambient light, the brighter the product backlight, the darker the ambient light, the darker the product backlight.

Projection function

1. In the time mode, press the【project】 to turn on the projection function, and the projection lamp defaults to high brightness. press the【project】 to switch the brightness of the projection lamp, the sequence is: high→low→off. (As shown in Figure 5)
2. In the projection function on state, long press【project】, the projection screen will rotate 180°. The projection column is adjustable: front 90°,back 90°.

FM radio function

1. In the time mode, press the【radio/sleep】to turn on the radio function. “ON” will be displayed first, and then the FM frequency will be displayed. (As shown in Figure 6)
2. Press the【radio/sleep】key, after the display shows “ON”, press the【radio/sleep】key again to select the time to turn off the radio. The sequence is: 05, 10, 15, 30, 45, 60, 75, 90. (For example: select “05”, the radio will automatically turn off after playing for 5 minutes)
3. After turning on the radio,press the【▲】/【▼】 to select channels manually. Long press the 【▲】/【▼】 to select channels automatically.
4. After turning on the radio,press the【vol】 to adjust the volume. The screen will display “L10”, press the【▲】/【▼】to adjust the volume from “L00” min to “L15” max. (As shown in Figure 7)
5. After turning on the radio,press 【 】key to directly turn off the radio and return to time mode.

The radio can store up to 10 stations：

1. Turn on the radio and search for your favorite station.

2. Press and hold the【set】until “01” appears. Press set again to save station 01.(As shown in Figure 8)

3. Press【▲】/【▼】to select other stations you like. Then press and hold【set】until “01” appears. Press【▲】/【▼】and “02” appears. Press 【set】 to save station 02.

4. Repeat step 2 to step 3 above to set up station 3 to station 10.

5. In the radio mode, press the 【set】to listen to the saved stations directly.

6. If you want to change a saved station, simply repeat the save station step, and the new selected station will replace the old one.

Temperature and humidity function

1. Product power on, the default display ℃, long press【▼】switch temperature unit (℃ / ℉) (As shown in Figure 9)
2. Indoor temperature range: 0-50℃; Indoor humidity range: 20%-95%.

Charging function

There is a USB output port on the side of the product, which can be used to charge cell phones or other electronic devices through the USB output with an output voltage of 5V in the state of using Type-c power cable connection for power supply.(as shown in Figure 10)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>