CG MOBILE TJ14 Wireless Earphones User Guide
- June 1, 2024
- CG MOBILE
Table of Contents
CG MOBILE TJ14 Wireless Earphones
Description
Content
- TJ14 TWS Earphones
- Type-C USB Charging Cable
- Quick Guide
Product Specification
- Bluetooth: V5.3
- Frequency Range: 2402-2480 MHz
- Sensitivity: 1013dB
- Impedance: 32 ohm+15%
- Input : DC 5V / 300 mA
- Earphones Battery Capacity : 30 mAh x 2
- Charging Pod Battery Capacity : 300 mAh
- Charge Time : 1.5 hours
Charging for Earphones:
Fully charge the battery for 1-2 hours before using the earbuds for the first
time, or when they have been unused for extended periods. Put the earbuds into
the charging case, and they will charge automatically. The indicators of
earbuds will be lit on red. The indicators will be lit-on blue for 1 second
and then be off once the earbuds are fully charged.
Charging for Charging Case
When the charging case is connected with a charger (or computer USB port) by a
charging cable, the indicators of the charging case will flash in red. When
the charging case is fully charged, the indicators will be lit red.
NOTE
When the charging case is out of battery, the earbuds will not turn on/off
automatically when removed from or placed back into the charging case. In this
case, turn the earbuds on/off manually.
First Use & Pairing
Auto Power-On & Pairing
Take the earbuds out of the charging case, the earbuds will automatically
power on and enter into pairing mode.
Connect
Turn on the device’s Bluetooth setting. The indicator of earbud flashes red and blue alternatively. Search for and choose TJ14 to pair, your device will show “connected”. The indicator of the earbud will be off.
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
Power-Off
Auto Power-Off
Put L&R earbuds into charging case, the earbuds will automatically power off.
Manual Power-Off
- Touch the MFB for 5 secs on both earbuds to power off the earbuds.
- The earbuds will automatically turn off when without pairing for 5 mins.
Wearing
Insert the earphones directed towards your ear canal. Twist gently until the
earbuds fit comfortably and get a better sound experience.
Control
Reset
If you have a problem connecting the earphones to your device, don’t worry
about it, please follow the steps below:
- Make sure all devices have turned off the Bluetooth Function. Clean all the pairing records from the Bluetooth list if needed.
- Take the earphones out of the case, tap either earphone 5 times quickly, the prompt sound will be activated, then follow the pairing step as instructed.