LUTRON DVRF-6L Smart Hub Pico Remote Control and Dimmer User Guide

LUTRON DVRF-6L Smart Hub Pico Remote Control and Dimmer

Welcome and thank you for purchasing a Caséta dimming kit.

Before you install the dimmer, please watch the installation video at www.casetawireless.com/support.

We hope you enjoy the convenience of Caséta!

Product Information

The Lutron Smart Hub, Pico remote control & dimmer package comes with the following:

• Dimmer (DVRF-6L)
• Claro wallplate (CW-1)
• Pico remote control (PJ2-3BRL)
• Wire connectors
• Lutron Smart Hub (L-BDG2 or L-BDGPRO2)
• Screws
• Power Supply (T-5DC-USB)
• Ethernet Cable

It works with energy-efficient dimmable light bulbs such as LED up to 150 W, Halogen up to 600 W, and Incandescent up to 600 W. However, dimmable LED light bulbs vary in their dimming performance. If flickering or turning off occurs, please visit www.casetawireless.com/lowend for information on adjusting the dimmer for the best bulb performance.

For a complete list of compatible dimmable LEDs, please visit www.casetawireless.com/bulblist.

Contents supplied

Usage Instructions

Quick-Start Guide
Before installing the dimmer, watch the installation video at www.casetawireless.com/support

Tools You’ll Need

• Flat-head screwdriver
• Pliers
• Phillips-head screwdriver

Specification

Works with energy-efficient dimmable light bulbs:

NOTE:
You can mix and match dimmable LED, halogen, and incandescent light bulbs with Caséta dimmers.

Dimmable LED light bulbs vary in their dimming performance. If you’re using these bulbs and they flicker or turn off, please visit www.casetawireless.com/lowend for information on adjusting the dimmer for best bulb performance.

For a complete list of compatible dimmable LEDs, please visit www.casetawireless.com/bulblist.

Installation for Lights with One Wall Switch (Single Pole)

1. Turn power off at circuit breaker!
2. Remove existing switch from wall.
3. Disconnect all three wires* from the switch.
4. Ganging and Derating: Multi-gang installations may reduce the dimmer’s maximum wattage rating. See the chart below for maximum wattage information.
   • Single gang: LED 150 W or Incandescent & Halogen 600 W
   • Double gang: LED 150 W or Incandescent & Halogen 500 W
   • Triple gang: LED 150 W or Incandescent & Halogen 400 W
5. Connect the bare copper (or green) ground wire from the wallbox to the green wire on the dimmer using one of the large supplied wire connectors.
6. Connect either of the remaining wires from the wallbox to the black wire on the dimmer using one of the large supplied wire connectors.
7. Connect the remaining wire from the wallbox to the red wire on the dimmer using one of the large supplied wire connectors.
8. Cap the blue wire coming from the dimmer with the small supplied wire connector. The blue wire is not used for single pole installations.
9. Mount the dimmer using the mounting screws provided, leaving them loose for this step.
10. Attach the adapter to the dimmer using the screws provided.
11. Tighten the mounting screws on the dimmer.
12. Snap-on the wallplate.
13. Turn the power on at the circuit breaker.

Installing your dimmer

1. Turn the power off at the circuit breaker!
   WARNING: SHOCK
   HAZARD! May result in Serious Injury or Death. Turn off the power at the circuit breaker or fuse before installing.
   Important note:
   We’ve included instructions for when a single switch is controlling the lights. For installation instructions when two or more switches are controlling a light, please visit www.casetawireless.com/3way for complete installation instructions and how-to videos.

2. Remove existing switch from wall
   Remove the wallplate from switch. Remove the switch and pull it away from the wall.
   Disconnect all three wires* from the switch.
   If your switch has more than 3 wires attached, see the “Installing Caséta in a 3-way switch application” video at www.casetawireless.com/3way.

3. Ganging and Derating Important note:
   Multi-gang installations may reduce the dimmer’s maximum wattage rating. See the chart below for maximum wattage information.
   Maximum wattage derating chart
   (120 V~ 50/60 Hz) Load Type| Single gang| Double gang| Triple gang
   ---|---|---|---
   LED| 150 W| 150 W| 150 W
   or
   Incandescent & Halogen| 600 W| 500 W| 400 W

For maximum wattage information when mixing light bulb types see www.casetawireless.com/ganging.

4. Connect the dimmer

5. Connect the bare copper (or green) “ground” wire from the wallbox to the green wire on the dimmer using one of the large supplied wire connectors.

6. Connect either of the remaining wires from the wallbox to the black wire on the dimmer using one of the large supplied wire connectors.

7. Connect the remaining wire from the wallbox to the red wire on the dimmer using one of the large supplied wire connectors.

8. Cap the blue wire coming from the dimmer with the small supplied wire connector. The blue wire is not used for single pole installations.
   Note: Wire colors depicted in this install guide may not match what is in your walls.

9. Mount the dimmer
   Use the mounting screws provided, leaving them loose for this step.

10. Attach the wallplate

11. Attach the adapter to the dimmer using the screws provided.

12. Tighten the mounting screws on the dimmer.

13. Snap-on the wallplate.

14. Turn power on at circuit breaker

Using your controls

Replacing light bulbs using FASS
Pull the FASS out on the dimmer to remove power at the light socket.

To restore the original factory settings please go to www.lutron.com/restore.

Important notes:

1. For indoor use only.
2. Operate between 32 ˚F (0 ˚C) and 104 ˚F (40 ˚C).

Using your Caséta by Lutron kit

1. Install the Lutron Smart Hub
   • A. Connect the smart hub to your Wi-Fi router using the Ethernet cable.
   • B. Connect the power cord to the smart hub and plug it into an outlet.
2. Download the Lutron app and walk through setup

Pairing the dimmer and Pico remote control

1. Press and hold “off” button on the dimmer
2. Press and hold “off” button on remote

Device Ratings

• Dimmer Pico remote control

• DVRF-6L 120 V~ 50/60 Hz PJ2-3BRL 3 V- 10 mA (1) CR2032 battery (included)

• Lutron Smart Hub *
  L-BDG2 or L-BDGPRO2 5 V- 300 mA Power supply T-5DC-USB

• Wallplate Bracket PICO-WBX-ADAPT

  • Input: 100–240 V~ 50/60 Hz 100 mA
  • Output: 5 V- 550 mA

Connect to a Class 2, LPS, or SELV, limited energy (<15 W) power source only.

Troubleshooting

out.
• Breaker is OFF or tripped.
• Light not properly installed.
• Wiring error.
• FASS switch on the dimmeris in the Off position.
Light does not respond to Pico remote control.| • The dimmer is not properly paired with the Pico remote control;
The Pico remote control can be paired with the dimmer using the Lutron app.
• The dimmer is already at the light level the Pico remote control is sending.
• The Pico remote control is outside the 30 ft (9 m) operating range.
• The Pico remote control battery is low.
• The Pico remote control battery is installed incorrectly.
• Bulbs turn off while being dimmed.
• Bulbs turn on at high light level but do not turn on at a low light level.
• Bulbs flicker or flash when dimmed to a low light level.| Verify bulbs are marked dimmable and visit www.casetawireless.com/lowendfor information on adjusting the dimmer for best bulb performance.
Load is Off and the light bar blinks 4 times, pauses, and repeats.| The dimmer is in Over Temperature Protection (OTP) mode.
• See Step 3 Ganging and Derating. Ensure that the dimmer is not overloaded.
• Reset the dimmer by using the Front Accessible Service Switch (FASS); See Using your Controls section. Pull out the FASS and push it back in.

Important Note
We’ve included instructions for when a single switch is controlling the lights. For installation instructions when two or more switches are controlling a light, please visit www.casetawireless.com/3way for complete installation instructions and how-to videos.

1. For indoor use only
2. Operate between 32 ˚F (0 ˚C) and 104 ˚F (40 ˚C)

Go to www.casetawireless.com/support for additional troubleshooting suggestions.

Note:
Wire colors depicted in this install guide may not match what is on your walls.

Disclaimer:
This is a general overview of installation and usage instructions. Please refer to the user manual/instructions provided with your product for detailed and specific instructions. For any further assistance, please contact customer support.

FCC STATEMENT

CAUTION
Use only with permanently installed fixtures with dimmable LED, halogen, or incandescent lamps.

To avoid overheating and possible damage to other equipment, do not use to control receptacles, motor-driven appliances, or transformer-supplied appliances.

CAUTION:
Risk of Fire, Explosion, Leakage, and Burns. Do Not Recharge, Disassemble, Heat Above 212 °F (100 °C) or Incinerate. This product contains a lithium button/coin cell battery. Keep batteries away from children. If a new or used lithium button/coin cell battery is swallowed or enters the body, it can cause severe internal burns and can lead to death in as little as 2 hours. Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep the batteries away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. The battery in this device contains Perchlorate Material — special handling may apply. For more information, visit www.dtsc.ca.gov/hazardouswaste/perchlorate.

Codes
Install in accordance with all national and local electrical codes.

Grounding
When no “grounding means” exist in the wall box, the National Electrical Code (NEC®) allows a control to be installed as a replacement if 1) a nonmetallic, noncombustible faceplate is used with nonmetallic attachment screws or 2) the circuit is protected by a ground fault circuit interrupter (GFCI). When installing a control according to these methods, cap or remove the green wire before screwing the control into the wall box.

Use of the HomeKit logo means that an electronic accessory has been designed to connect specifically to iPod, iPhone, or iPad, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with an iPod, iPhone, or iPad may affect wireless performance.

FCC/IC Information
For FCC/IC information, please visit www.lutron.com/fcc- ic.

Warranty

For warranty information, please visit www.casetawireless.com/warranty.

Double your warranty

Love Caséta dimmers?
Have ideas for making them better? Tell us what you think and we’ll extend your warranty by 1 year. www.casetawireless.com/register.

The Lutron logo, Lutron, Claro, Caséta, FASS, the Lutron Caséta & RA2 Select app logo, the design of the Pico remote, and Pico are trademarks or registered trademarks of Lutron Electronics Co., Inc. in the US and/or other countries. Apple, iPod, iPhone, and iPad are trademarks of Apple Inc., registered in the U.S. and other countries. HomeKit is a trademark of Apple Inc. App Store is a service mark of Apple Inc., registered in the U.S. and other countries. All other product names, logos, and brands are the property of their respective owners.

© 2015-2023 Lutron Electronics Co., Inc.

Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299, U.S.A.

References

• Installing Caséta for a light with two switches | Lutron
• Lutron Support Center | Lutron
• Capacity Derating Charts
• casetawireless.com/register
• Application Notes | Caséta Wireless | Lutron
• casetawireless.com/warranty
• dtsc.ca.gov/hazardouswaste/perchlorate
• lutron.com/fcc-ic
• How to Factory Default Caseta Dimmers, Switches, and Fan Controls | Lutron

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>