VALBERG 972442 Purifying Fan Instruction Manual

VALBERG 972442 Purifying Fan

Thank you!
Thank you for choosing this VALBERG product. VALBERG products are chosen, tested, and recommended by ELECTRO DEPOT, so you can be sure you are getting a top-quality, easy-to-use product that won’t let you down. We’re confident your new device will be a pleasure to use every day! Welcome to ELECTRO DEPOT.

Product Overview

Parts

• A. Remote control storage slot
• B. Air outlet
• C. Infrared sensor receiver
• D. Base
• E. AC adapter and plug
• F. Control panel and display
• G. Filter replacement icon
• F. Ionisation icon
• H. Fan speed icon
• I. Time and temperature display
• J. Sleep mode icon
• K. AI mode icon
• L. Mode button
• M. Oscillation button
• N. Power button
• P. Timer button
• Q. Fan speed button
• R. Air inlet with filtration system (x2)
  1. Cover
  2. Pre-filter
  3. HEPA filter
• S. +/- button

1. Unpack the product. Remove all the labels from the product. Check that it is complete and in a good condition. If the unit is damaged or faulty, do not use it and take it to your retailer or after-sales service centre.
2. Keep all packaging out of the reach of children. There is a risk of accidents if children play with packaging materials.

Intended use

• This product is for domestic use only. It has not been designed for industrial or professional use.
• Any other use may damage the product or cause injury.

Specifications

• Model: 972442
• Main unit with an AC adapter
  • Operating voltage: 100-240 V~, 50/60 Hz, 1.5 A
  • Power: 33 W
  • Noise level: ≤61 dB
  • Operating temperature: 0-40 °C
  • Main unit size (W x D x H): 255 x 255 x 1,056 mm
  • Weight: 7.6 kg
  • Protection class: Class II
• Remote control
  • Battery: 2x 1.5 V AAA batteries (not supplied)
  • Operating range: 5 metres

Before first use

Assembling the filtration system
The ventilator boasts 2 filtration systems on each side of the base. Follow the below instructions to install them.

1. Make sure that the unit is switched off and unplugged. Remove the air inlet cover and pre-filter.
2. Remove the protective plastic film from the HEPA filter and install the filter.
3. Reinstall the pre-filter, making sure to align the slots in the base with the ridges on the pre-filter, then push the top until it clicks into place.
4. Reposition the air inlet cover and make sure that it is secured in place.
5. Inserting the remote control batteries.
6. Slide the remote control cover in the direction indicated by the arrow.
7. Insert the 2x 1.5 V AAA batteries (not supplied), making sure to match the polarity, as indicated in the battery compartment.
8. Replace the cover.
9. The remote control is now ready for use. Point the remote control at the infrared sensor on the display (within 5 metres). Make sure there are no obstacles between the fan and the remote control.

WARNING: Do not use rechargeable batteries with this product.

Before first use

• Place the fan on a stable horizontal surface.
• Make sure the air inlets/outlets are unobstructed. Do not cover the fan.

Operation

1. Insert the connector into the AC adapter socket on the back of the unit. Then connect the plug to the mains socket.
2. Press the button to switch on the unit. The current temperature will be displayed.
3. Press the button or button on the fan and remote control, respectively, to select one of the following modes:
4. Press the button once to enter the timer mode. Next, press the fan’s button repeatedly or use the +/- buttons on the remote control to set the timer so that the fan will turn off after 1-12 hours (depending on the time set). To deactivate the timer, set the time to 0h.
5. Press the button to oscillate the fan and rotate it 60 degrees. Press the button to stop it.
6. To turn off the fan, press the button. The screen will then turn off. Unplug the unit from the mains socket to completely switch it off.

Cleaning and maintenance

CAUTION!

• Always unplug the fan before cleaning it.
• When cleaning the unit, never use flammable or abrasive products (such as benzene or white spirit), metal brushes, scouring pads, wire sponges or sharp utensils.
• Never immerse the unit, cable or AC adapter plug/ connector in water.
• Regularly clean your unit and keep it dust free to optimise its performance, reduce the need for repairs and ensure product longevity.
• Clean the exterior with a soft, damp cloth. Make sure that no liquid enters the unit.

Filter cleaning
If you use the fan regularly, clean the pre-filters once every 2 weeks and replace the HEPA filter every 6 months. The filter replacement icon will be displayed whenever the HEPA filter needs replacing.

1. Remove the air inlet covers and pre-filters. Vacuum them or wipe them with a soft, damp sponge. Dry them thoroughly.
2. Remove the HEPA filters and insert the new ones.
3. Reinstall the pre-filters and air inlet covers.
4. To reset the replacement icon, press and hold the button until it is no longer displayed.

Storage

• Always unplug the unit before storing it.
• Store the unit in a fresh, dry and dust-free place, out of the reach of children and pets.
• Please retain the packaging and use it to store your unit when it is not in use for an extended period of time.

WARRANTY CONDITIONS

This product is guaranteed against faults caused by defects in manufacturing or the materials used for two years, starting from the date of purchase. This warranty does not cover defects or damage caused by failure to install the device correctly, incorrect use of the product, or excessive wear and tear. proof of purchase required.

ELECTRO DEPOT
1 route de Vendeville
59155 FACHES-THUMESNIL – FRANCE

References

• valberg.de is available for purchase - Sedo.com
• Tienda de electrodomésticos y electrónica | ELECTRO DEPOT

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>