LUTRON DVRF-6L-WH Caseta Diva Smart Dimmer Instructions

LUTRON DVRF-6L-WH Caseta Diva Smart Dimmer

Contents supplied

Tools you’ll need

Installing your dimmer

Installation for lights with one wall switch (single pole)

Turn the power off at the circuit breaker ****

WARNING: SHOCK HAZARD may result in serious injury or death. Turn off the power ar o the circuit breaker Of the fuse before insta111119.

Important note
We’ve included instructions for when a song e switch is controlling the lights. For 11stalation instructions when two or ma<e sw this are controlling a light. p\ease visit www.casetawireless.com/3way for comptete lnsta!lat.ion 1t1structlons and how~to videos.

Remove the existing switch from the wall

Remove the wallplate trc«n switch. Remove the switch and pull it away from the wall. Disconnect all three wires’ from the switch.

• If your switch has more than 3 wires attached. see the “Installing Caséta Wireless in a 3-way switch application” video at www.casetawireless.com/3way

Ganging and Derating Important note:
Multi-gang installations may reduce the dimmer’s maximum wattage rating. Sæ the chart below or maximum wattage information,Maximum wattage derating chart (120 50/60 Hz)
For rnaxirnurn wattage information light bulb types see www.casetawireless.com/ganging
Connect the dimmer

• Connect the bare copper (or green} ground” wire from the wall box to the green Wre on the dimmer using one of the largely supplied wire connectors.
• Connect either of the remaining våes from the wall box to the black wire on the dimmer using one Of tne large supplied wire connectors.
• Connect the remaining wire from the wall box to tne wire on the dimmer using one of the supplied web connectors.
• Cap the blue wire coming from the dimmer with the small supplied connector. The blue wire is not for single-pee installations,

Note: Wire colors depicted in this install guide may not match what is on your walls.

Mount the dimmer

• using the screws provided.

Attach the wallplate
Attact to the dinner using the screws provided and the snap-on wall plate.

Turn the power on at the circuit breaker

To use your Caséta Wireless system

With a smartphone or tablet (Smart Hub required, sold separately)

The Caséta Wireless Diva Smart Dimmer can be controlled from a smartphone when used with the Lutron Smart Hub (Srnan Bridge) and the Lutron app. If you are using the dinner and remote control with the Iutrco Smart Hub follow the instructions below.

Note: If you æe using the dimmer and remote control with another manufacturers bridge, please refer to that manufacturer’s instructions cc

Download the Lutron app

Launch the Lutron app

Use the Lutron app to complete ALL remaining steps

Without a smartphone or tablet

(Smart hub not required)

Pairing the dimmer and Pico remote control

• Press and hold the “off” button on the dimmer
• Press and hold the “off” button on remote Changing the favorite light level on the Pico remote control (sold separately)
• Set the desired light level on a dimmer
• Press and hold the “favorite” button remote

For advanced features, tips for using Caséta Wireless dimmers with LEDs and CFLs. the compæte Caséta Wireless product line. and more, please visit www.casetawireless.com/features

Using your controls

Replacing light bulbs using FASS
Pun the FASS switch out on the in-wall dimmer to remove power at the light socket.

Important notes

1. For indoor use
2. Operate between 32 (O C) and 104 ‘F

Troubleshooting

Go to mvw.casetawireless.com/support for additional troubleshooting suggestions.

Works with energy-efficient dimmable light bulbs
NOTE: CFLs, as well as halogen and tncancjescent Ight bulbs. with Caséta Wireless dimmers.
Dimmable LED and CFL t bulbs vary in their dimming performance. If you’re using these bulbs and they ticker or turn off. please visit www.casetawireless.comnowend for information on adjusting the item.er fancy best bulb performance.
For a complete list of compatible(e dimmable I-FDs and CPLS, please viSt www.casetawireless.com/bulblist

Set the desired light level on a dimmer

CAUTION
Use coly with Krtnanentb/ installed fixtures with dimmable LED, and dimmable CFL. halogen, or incandescænt, lamps. To avoid overheating and possible damage to other equipment. do not use to control receptacles, motor-driven appliances, ortransformer-supplea appearances. Install in accordance with all national and local

Grounding
When no “grounding means’ exist in the wall box, the National Electncai Ccxie (NEC) allows a control to be installed as a replacement if 1) a nonmetallic, noncombustible faceplate is used with nonmetallic attachment or 2) the circuit is protected by a ground fault circuit interrupter (GFCI). When installing central according to these methods, cap or remove green waste before controlling into the wall box.

Warranty

For warranty information, please visit www.casetawireless.com/warranty

Double your warranty

Iove products?
Have ideas for making them better? Tell us what you think ard we’ll extend your warrætty by 1 year. www.casetawireless.com/register

FCC STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15of the fcc rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with theinstructions,may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different  from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure conditions without restriction. FCC ID: 2BAO3-AM003

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>