goobay 45801 LED Solar Wall Light with Motion Sensor Instruction Manual

goobay 45801 LED Solar Wall Light with Motion Sensor

Product Information

The LED Solar Wall Light with Motion Sensor is a battery-operated wall light with 14 LEDs, 12 in the front and 2 in the rear. The light has a neutral white color with a temperature of 4000 K and a luminous flux of 220 lm. The LED beam angle is not specified, but the max luminous range is 5-6 m. The light has a motion sensor that uses infrared passive (PIR) technology with a detection range of 2-6 m and a detection angle of 120 degrees. The light is protected against water jets and has an IP65 protection level. The light is not dimmable, and the operating temperature is not specified. The product comes with a rechargeable 18650 Li-Ion battery, which is exchangeable, with a capacity of 1200 mAh. The battery can last for up to 3 days with 6 hours of direct sunlight, and it takes approximately 7-8 hours to fully charge the battery. The light also comes with a polycrystalline silicon solar panel with a peak wattage of 0.7 Wp.

Product Usage Instructions

1. Before installation, read the safety instructions and product description carefully.
2. Choose an appropriate location to install the light where there is enough sunlight to charge the battery. Keep a distance of 1 meter from any illuminated object.
3. Use the mounting template and included mounting material to install the light on a wall or other suitable surface at a height of 2-4 meters. Ensure that the screws are securely fastened.
4. To turn on the light, flip the switch located on the back of the light to the “On” position.
5. The light will automatically turn on when it detects motion in its detection range and when the ambient light level is low enough. The light will turn off after 10 seconds of no motion.
6. To replace the battery, carefully remove the battery compartment cover and replace the battery with a new 18650 Li-Ion battery.
7. Do not attempt to disassemble or modify the light. The light is maintenance-free, but it should be periodically cleaned with a soft cloth to remove any dirt or debris that may accumulate over time.
8. When disposing of the light, follow local regulations for electronic waste disposal.

Specifications

General Information
Power of LEDs| 1.5 W
Number of LEDs| 14 (12 in the front, 2 in the rear)
Protection level| IP65
Dimmability| not dimmable
Operating temperature| -20 °C ~ +50 °C
Housing colour| black| white
Dimensions| 144.5 x 96.0 x 79.0 mm
Weight| 192 g
Rechargeable battery
Specifications| 18650 Li-Ion, 3.7 V , 1200 mAh
Exchangebility| exchangeable
Max. operating time in days with 6 h di- rect sunlight| 3 days
LED light
Light colour| neutral white
Light temperature| 4000 K
Luminous flux| 220 lm
LED beam angle| 90°
Max. luminous range| 5-6 m
Colour rendering index| 80 Ra
Service life| 35000 h
Motion detector
Sensor type| infrared passive (PIR)
Detection angle| 120°
Detection range| 2-6 m
Installation height| 2-4 m
Switch-off delay| 10 s
Solar panel

Voltage| 3.7 V ****
Type| polycrystalline silicon
Watt Peak| 0.7 Wp

Symbols used

Safety instructions

In general
The user manual is part of the product and contains important information for correct use.

• Read the user manual completely and carefully before use. The user manual must be available for uncertainties and passing the product.
• Keep this user manual.
• Do not open the housing.
• Do not modify product and accessories.
• Do not short-circuit connectors and circuits.

A defective device may not be put into operation, but must be protected against further use.

• Use product, product parts and accessories only in perfect condition.

The lamps cannot be replaced! In case of questions, defects, mechanical damage, trouble and other problems, non-recoverable by the documentation, contact your dealer or producer. Not meant for children. The product is not a toy!

• Secure packaging, small parts, and insulation against accidental use.
• Never look directly into the light source.
• Do not aim the beam of the light into the eyes of other persons, animals or reflective surfaces.

The eyes can be damaged!

• Avoid stresses such as heat and cold, moisture and direct sunlight, microwaves, vibrations, and mechanical pressure.
• Follow local installation and building regulations.
• Do not touch during or immediately after use.
• Avoid proximity to flammable surfaces and substances.
• Do not cover the product.
• Do not use in sealed environments.

Battery hazards
The batteries are replaceable.

• Keep the batteries out of the reach of children.
• Never use batteries when they are dented, leaked or damaged.
• Remove leaked, deformed or corroded batteries from the product and dispose them by appropriate protectives.
• If a battery has leaked, avoid contact with skin, eyes and mucous membranes. If necessary, rinse affected areas with water and seek medical attention immediately.
• Do not deform, burn or disassemble the battery. Mechanical damage can cause gaseous substances to escape, which can be highly irritating, flammable or toxic.
• Do not expose the battery to heat, for example in the form of radiant heat, or fire. Extreme heat can lead to explosion and/or leakage of corrosive liquid.
• Do not short-circuit the battery or immerse it in liquids. There is a danger of: Explosion, fire, heat, smoke and/or gas.

Description and function

Product
This product is a battery-operated LED solar wall light with integrated infrared motion detector. Objects are detected by the sensor in the detection area. In case of changes in movement and twilight, the LED light is switched depending on the operating mode. The integrated battery is charged by the solar panel.

Scope of delivery
LED Solar Wall Light with Motion Sensor, mounting template, mounting material, User Manual

Operating Elements
See Fig. 1.

1. Fixing eyelets
2. Solar panel
3. Motion sensor
4. Switch
5. LEDs
6. Battery compartment

Intended use

This product is intended exclusively for private use and its intended purpose. This product is not intended for commercial use. We do not permit using the device in other ways like described in chapter “Description or Function“ and „Safety Instructions“. Not attending to these regulations and safety instructions might cause fatal accidents, injuries, and damages to persons and property. A distance of 1 m from the illuminating object must be maintained IP65: This product is dust-proof against touch and protected against water jets.

Preparation

• Check the scope of delivery for completeness and integrity.

Installing

WARNING! Risk of electric shock

• Pay attention to current-carrying or other lines, lying behind plaster and do not damage them!

CAUTION! Risk of falling

• Keep yourself safe at the product’s set-up location! The surface must be stable. The supplied mounting material is only suitable for concrete and stone walls. Other dowels must be used for mounting on other surfaces. Plants, street lights, reflective surfaces and ventilation openings must not be near or in the detection range. There must be no flammable objects in the vicinity. A distance of 1 m from the illuminated object must be maintained.

Recommended installation location: as sunny as possible, 2-4 m installation height.

1. Use the enclosed mounting template and, if necessary, a spirit level to mark the mounting holes.
2. Drill the required number of mounting holes with a Ø 6 mm drill bit.
3. Insert the required number of dowels and fixing screws into the holes. Allow the fixing screws to protrude about 4 mm from the wall.
4. Hang the product on the fixing screws from above.
5. Carefully tighten the fastening screws. If the solar light does not work immediately, place or hang it in a sunny spot for a few days so that the battery can charge via the solar panel.

Operating

The range cannot be adjusted. It can be varied due to the mounting height (see Fig. 2). The switch-off delay cannot be set. The trigger sensitivity cannot be set. You can select between 3 modes via the switch.

• Press the switch 1x briefly to switch to the next mode.

See Fig. 3.
Mode A:
The LEDs on the front and back light up at full power after being triggered by motion in the detection area and switch to about 20 % power after approximately 10 seconds without being triggered again. The LEDs on the front and back switch on automatically at 20 % of the maximum power for about 5 hours at dusk or an ambient brightness of ≤ 30 lx without detecting any motion and then switch off again.

Mode B:
The LEDs on the front and back light up at full power after being triggered by motion in the detection area. After approximately 10 seconds without being triggered, the LEDs on the front switch off until motion is detected again. The LEDs on the rear side light up with 20 % of the maximum power for about 5 hours and then switch off again. The LEDs on the rear side switch on automatically at 20 % of the maximum power for about 5 hours at dusk or an ambient brightness of ≤ 30 lx without detecting any motion and then switch off again.
Mode C:

The product is completely switched off.

Removing and charging the battery

The battery can be replaced and optionally charged with the help of a suitable charger.

1. Loosen the 7 screws on the battery compartment (6).
2. Remove the cover from the battery compartment.
3. Carefully remove the battery.
4. Charge the battery using a suitable charger or replace it with a battery of the same type (18650 Li-Ion, 3.7 V , 1200 mAh).
5. Insert the battery in the marked polarity.
6. Place the cover on the battery compartment and fasten it again with the screws.

Maintenance, Care, Storage and Transportation

The product is maintenance-free.
NOTICE! Material damage

• If the batteries are not used for a longer period of time, charge them every 3 months to maintain the capacity.
• Only use a dry and soft cloth for cleaning.
• Do not use detergents or chemicals.
• Remove batteries/rechargeable batteries when not in use.
• Store the product out the reach of children and in a dry and dust-protected ambience when not in use.
• Store cool and dry.
• Keep and use the original packaging for transport.

Disposal instructions

Product
According to the European WEEE directive, electrical and electronic equipment must not be disposed of with consumers’ waste. Its components must be recycled or disposed apart from each other. Otherwise contaminative and hazardous substances can damage the health and pollute the environment. As a consumer, you are committed by law to dispose of electrical and electronic devices to the producer, the dealer, or public collecting points at the end of the devices lifetime for free. Particulars are regulated in national right. The symbol on the product, in the user manual, or at the packaging alludes to these terms. With this kind of waste separation, application, and waste disposal of used devices you achieve an important share to environmental protection.

Battery
(Rechargeable) batteries must not be disposed of with household waste. Their components have to be supplied separately to the recycling or disposal, because toxic and dangerous ingredients can harm the environment if not disposed of sustainably. As a consumer, you are obliged to return them at the end of their service lives to the manufacturer, the sales outlet or established for this purpose, public collection points for free. Details regulates the respective country‘s law. The symbol on the product, the instruction manual and / or the packaging draws attention to those provisions. With this kind of material separation, recovery and disposal of waste (rechargeable) batteries you make an important contribution to protecting our environment. D-34000-1998-0099

Packaging
Packaging can be disposed of free of charge at the suitable collection points – paper belongs in paper bins, plastics belong in yellow sacks and glass belongs in used glass bins.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>