easee Equalizer Amp Measuring Device User Guide
- June 9, 2024
- easee
Table of Contents
easee Equalizer Amp Measuring Device User Guide
Introduction
The information in this leaflet applies to Easee Equalizer Amp , unless
specified otherwise.
Read the Important product information guide in the product packaging or at
easee.com/manuals before using the product.
⚠ WARNINGS AND CAUTIONS
A Warning indicates a condition, hazard or unsafe practice that can result in
serious personal injury or death. A Caution indicates a condition, hazard or
unsafe practice that can result in minor personal injury or damage to the
product.
⚠ WARNING This product shall only be installed, repaired or serviced by an authorised electrician. All applicable local, regional and national regulations for electrical installations must be respected.
Optimal performance
The Equalizer Amp together with the Easee Equalizer makes it possible to
charge smarter, safer and faster without the need of a smart meter, if the
installation is scaled accordingly.
Technical specifications
Product overview
*Plug not included for the power cable.
Installation instructions
⚠ WARNING – This product shall only be installed,
repaired or serviced by an authorised electrician. All applicable local,
regional and national regulations for electrical installations must be
respected. – Turn off the power before you begin the installation. Use extreme
caution and follow instructions carefully.
https://easee.com/installer-app/
Install the Installer App on your phone by visiting easee.com/installer- app or scanning the QR code.
1 Equalizer Amp Mounting
- Mount the Equalizer Amp on the DIN rail (A) inside the fuse cabinet. If that’s not possible, attach the included DIN bracket (B) to a surface and then mount the Equalizer Amp.
2 Current sensors Attaching
- Attach current sensor(s) around each conductor either in front or behind the main fuse. The arrow on the sensor must point towards the load.
- Plug the current sensors, L1, L2 and L3, into their respective terminals 1, 2 and 3.
NOTE! Depending on national standards, the colour of the cables can vary from illustration.
3 Equalizer Amp Connecting
-
Connect the included power cable to a suitable power source. A separate fuse with a maximum rating of 16 A is recommended.
-
Find the RJ12 cable in the Equalizer box and connect it to an RJ12 terminal on the Equalizer Amp. The bottom RJ12 terminal is for connecting multiple Equalizer Amps.
CHECK LIST! Before powering up the Equalizer Amp, make sure that:
o The current direction is correct on the current sensors.
o The charging sites and the Equalizer Amp have the same phase sequence.
o The L1 current sensor is plugged into terminal 1, L2 sensor in terminal 2 and L3 sensor in terminal 3 on the Equalizer Amp. -
Power up the Equalizer Amp. You should see a flashing at the bottom right corner of the device.
4 Equalizer Setting up
Use the Installer App to configure the Equalizer on a site with multiple
circuits.
Before starting, make sure that the Equalizer and the master charger(s) are
connected to the same WiFi network. Also make sure you have NFC enabled on
your mobile phone.
- Go to “Ongoing sites”, or “Update existing site”, and select your site.
- Under “Site structure”, select “Add Equalizer”.
- Enter the WiFi information (the same network the chargers are connected to).
- Hold the mobile phone to the front of the Equalizer to transmit the WiFi details. The Equalizer cannot receive the information if it’s powered on.
- Connect the Equalizer to the Equalizer Amp with the RJ12 cable.
Practical details
LED colours meaning
White, fast flashing Booting White, breathing every 10s Normal operation
Red / white, switching No WiFi added Red, flashing No data from power
meter Red, breathing every 10s Error Purple, breathing every 10s Offline
operation
Warranty
The device is free from material defects and is in accordance with laws and
regulations for consumer protection in the country where the product is
purchased. All correctly installed Easee hardware is covered by our 3 years
limited warranty. Some countries may have extended warranty.
Maintenance
This product requires no maintenance. If it needs to be repaired, please
contact your Easee supplier.
Returns and complaints
Contact your distributor or Easee Customer Support at
easee.support regarding the return and complaint of
your product.
The information in this document is for information purposes only, is provided as is, and may be subject to change without notice. Easee AS including its subsidiaries does not accept any liability for the correctness or completeness of the information and illustrations, and is not liable or responsible for your considerations, assessments, decisions or absence of such, or other use of the information in this document.
No part of this publication may be re-published, reproduced, transmitted or re-used in any other form, by any means or in any form, for your own or any third-party’s use, unless otherwise agreed with Easee or its subsidiaries in writing. Any permitted use shall always be done in accordance with good practice and ensure that no harm may be caused to Easee or by misleading the consumer.
Easee and Easee products, product names, trademarks and slogans, whether registered or not, are Easee’s intellectual property and may not be used without Easee’s prior written permission. All other products and services mentioned may be trademarks or service marks of their respective owners.
January 2023 Version 1.00 © 2023 by Easee AS. All rights reserved.
Easee AS Grenseveien 19 4313 Sandnes, Norway
www.easee.com
References
- Easee – Shaping the future of electricity
- Easee – Shaping the future of electricity
- Installer app | Easee International
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>