P1 Easee Equalizer User Guide
- May 15, 2024
- easee
Table of Contents
Easee Equalizer
Introduction
The information in this leaflet applies to Easee Equalizer P1 (E02-EQP) and
Easee Equalizer HAN (E02-EQ), unless specified otherwise.
Read the Important product information guide in the product packaging or at
easee.com/manuals before using the product.
Optimal performance
The Equalizer makes it possible to charge smarter, safer and faster if the
installation is scaled accordingly. To enable its true potential, the rated
value of the chargers circuit fuse should be as high as possible compared to
the main fuse.
Product overview
Technical specifications
General|
---|---
Dimensions Product| 110 x 110 x 27.5 mm (H x W x D)
Dimensions Product Packaging| 130 x 130 x 39 mm (H x W x D)
Permitted temperature| -20 °C to +50 °C
Weight| IP40
IP degree Supply| 5-30 V DC 100 mA (Equalizer P1)
20-32 V DC 30 mA (Equalizer HAN)
Cabling|
Cable length| 1.5 m
Custom made cable| RJ12 to RJ12 (Equalizer P1)
RJ12 to RJ45 (Equalizer HAN)
It can be extended using
an extension cable| up to 15 m (Equalizer P1)
up to 200 m (Equalizer HAN)
Max transmitted
power
| Radio | 25 mW at 863–870 MHz. |
|---|---|
| WiFi | 50 mW at 2.4–2.472 GHz. |
Connectivity
Easee Link RF TM and WiFi 1
HAN (NVE/AMS) (Equalizer HAN) or P1 (Equalizer P1) smart meter communication
Modbus connection to energy meter 2
Monitor power consumption with the Easee App
RFID / NFC reader
- WiFi is required for normal operation and for future software updates. Installations with multiple master chargers need to be connected to the same WiFi for load balancing to work. Easee Link RF 2(TM) via radio may be limited by walls, concrete or other obstacles.
- Only for supported meters.
Installation Customer setup
Follow these steps if you are a private customer installing the Equalizer in your own household.
-
HAN port Activation
In Scandinavia, the communication port on the smart meter is most likely not activated. Contact your utility company to open the HAN port for use with the Equalizer. If you are not in Scandinavia,skip to step 2. -
Easee App Download
Scan the QR code to download the Easee App and create a free account.easee.com/app -
Equalizer Setup
Add the Equalizer in the app, follow the on-screen installation guide and get ready to balance your energy smarter than ever before!
Installer setup
Follow these steps if you are an installer and use the Installer App to configure the Equalizer in large commercial installations or private households.
-
Installer App Download
Scan the QR code to download the Installer App and create a free account.
easee.com
/installer-app -
Equalizer Setup 2
Add the Equalizer to a new or existing charging site using the Installer App and follow the on-screen installation guide to set it up. -
Smart meter Connect
Connect the Equalizer to the smart meter using the provided cable. The Equalizer will appear in the Easee Portal after a while.
LED colours meaning
| White, fast flashing – Booting
---|---
| White, breathing every 10s – Normal operation
| Red / white, switching – No WiFi added 3
| Red, flashing – No data from power meter 4
| Red, breathing every 10s – Error 5
| Purple, breathing every 10s – Offline operation 6
| Touch the Easee logo in the middle to check power consumption:
| Blue, fast flashing – High power consumption
Blue, slow flashing – Low power consumption
Count the flashes for percentage – 1 flash (10%), 2 flashes (20%), up to 10
flashes (100%)
| Hold the Easee logo for 3 seconds to check connectivity.
You will see 2 flashes:
1st flash – Easee Link RF status
2nd flash – WiFi status 7
| Green – Connected
| Red – Not connected7
3 Use the Easee App to set up the WiFi.
4 Contact your utility company to activate the HAN port.
5 Go to http://easee.support.
6 Check your internet connection.
7 After booting, it can take a few minutes before Easee Link RFTM status
flashes green.
Practical details
Warranty
The device is free from material defects and is in accordance with laws and
regulationsfor consumer protection in the country where the product is
purchased. All correctly installed Easee hardware is covered by our 3 years
limited warranty.
Some countries may have extended warranty.
Returns and complaints
Contact your distributor or Easee Customer Support at
easee.support regarding the return and complaint of
your product.
The information in this document is for information purposes only, is provided
as is, and may be subject to change without notice. Easee ASA including its
subsidiaries does not accept any liability for the correctness or completeness
of the information and illustrations, and is not liable or responsible for
your considerations, assessments, decisions or absence of such, or other use
of the information in this document.
No part of this publication may be re-published, reproduced, transmitted or
re-used in any other form, by any means or in any form, for your own or any
third-party’s use, unless otherwise agreed with Easee or its subsidiaries in
writing. Any permitted use shall
always be done in accordance with good practice and ensure that no harm may be
caused to Easee or by misleading the consumer.
Easee and Easee products, product names, trademarks and slogans, whether
registered or not, are Easee’s intellectual property and may not be used
without Easee’s prior written permission. All other products and services
mentioned may be trademarks or service marks of their respective owners.
September 2023 – Version 1.01
© 2023 by Easee ASA. All rights reserved.
Easee ASA
Vassbotnen 23
4033 Stavanger, Norway
.easee.com
References
- Easee – Shaping the future of electricity
- Easee app | Easee International
- Installer app | Easee International
- Easee – Shaping the future of electricity
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>