easee 90501UK Equalizer User Guide
- June 4, 2024
- easee
Table of Contents
90501UK Equalizer
User Guide
90501UK Equalizer
IMPORTANT
Read carefully before use.
Keep it for future reference.
You can find the latest version of this manual, other languages, answers to
frequently asked questions, and other useful information with
ease.support.
Intended use
This product is intended for optimizing power consumption by performing an
automatic load balancing between the Easee Charging Robot(s) and the building.
It avoids overload and power interruption while charging the electric vehicle
(EV).
The product needs to be paired with a Charging Robot and connected to a
compatible smart meter with the cable provided. In order for the Equalizer to
work, the smart meter’s HAN port needs to be activated. The product may only
be operated with the approved operating parameters and under the specified
environmental conditions (see pages 5 and 9). Do not use the product if it is
damaged or does not function properly.
Uses other than those specified here are not permitted.
Product Overview
Technical specifications
General| Product (mm): H: 110 x W: 110 x D: 27.5
Packaging (mm): H: 130 x W: 130 x D: 39
Operating temperature: -20 °C to +50 °C
Weight: 110 g
IP degree: IP40
Supply: 20-32 VDC 30mA
RJ11 connector
---|---
Installation| Cable length: 1.5 m
RJ11 to RJ45 custom-made cable
Extended with an RJ45 adapter (up to 200 m)
Connectivity| Easy Link RFTM and WiFi
HAN connection to the energy meter
Monitor power consumption with the Easee app
RFID / NFC reader
WiFi is required for normal operation. When offline, it will continue to work via Easee Link RFTM.
Charging Robot Pairing
Before you start: make sure your Easee charger is connected to the same WiFi as you want the Equalizer to connect to. The Equalizer does not need to be connected to a power source during this step.
- Have the front side of the Equalizer facing the charger.
- Take it slowly forward so that it covers the light strip on the charger.
- When you hear a beep and the light strip lights up green, the pairing is complete.
If the pairing fails, wait 5 seconds and try again.
Fuse box Connecting
- Plug the Equalizer into a HAN port with the provided cable. In most cases, the HAN port will be inactive. You can still pair your Equalizer to the Charger, but it will not work until you contact your utility company to open the HAN port for 3rd party use. After around 30 seconds, it should start flashing in white while connecting to your WiFi. Once connected, it is automatically added to the Easy app!
- Place the magnetic backside of the Equalizer directly on a metallic surface. If a metallic surface is not available, fix the metallic disc with a screw on the wall and then snap the Equalizer to it.
NOTICE! For better communication with the Easee charger, place the Equalizer outside of the fuse cabinet. When outdoors, it should be protected from the weather, e.g. inside the fuse box (see page 9).
What do the LED colors mean?
White, fast flashing – Booting
White, breathing every 10s – Normal operation
Red / white, switching – No WiFi added
Red, flashing – No data from the power meter
Red, breathing every 10s – Error
Purple, breathing every 10s – Offline operation
Touch the Easee logo in the middle to check power consumption:
Blue, fast flashing – High power consumption
Blue, slow flashing – Low power consumption
Count the flashes for a percentage – 1 flash (10%), 2 flashes (20%), up to 10
flashes (100%)
Hold the Easee logo for 3 seconds to check connectivity. You will see 2
flashes:
1st flash – Easee Link RF status
2nd flash – WiFi status
Green – Connected
Red – Not connected
¹Use the Easee App to set up the WiFi.
²Contact your utility company to activate the HAN port.
³Go to http://easee.support.
4Check your internet connection.
Practical details
Charge faster| The Equalizer makes it possible to charge smarter, safer, and
faster if the installation is scaled accordingly. To enable its true
potential, the rated value of the charger’s circuit fuse should be as high as
possible compared to the main fuse. Even in 1-phase setups, we recommend using
a 3-phase cable to future-proof the installation.
---|---
Protection| The Equalizer is IP40. This means it has no protection against
water. If placed outside the house, it must be installed inside a cabinet
protected from the weather.
Standards| The EU Declaration of Conformity is available at the
following address: ease. support.
Max transmitted power| Radio: 100 mW at 863–870 MHz.
WiFi: 50 mW at 2.4–2.472 GHz.
Maintenance| This product requires no maintenance. If it needs to be repaired,
please contact your Easee supplier.
Storage| The product should be stored in a tempered, dry and well-ventilated
area in order to preserve the packaging and its contents. Relative humidity
should not exceed 80% and no corrosive gas should be present. Storage or
transportation environment should never exceed the limits provided in the
technical specifications (see page 5).
Disposal| This electronic equipment must not be disposed of in household
waste. For the return of old devices, free collection and acceptance points
may be available in your vicinity. Observe local regulations for correct and
environmentally friendly disposal.
Returns and complaints| Contact your distributor or Easee Customer Support at
ease. support regarding the return and complaint of your product.
Contact details| Easee AS
Grenseveien 19
4313 Sandnes, Norway
Org. nr: 920 292 046
You can find additional contact details for your country at
easee.com.
THIS DOCUMENT CONTAINS INFORMATION THAT IS SUBJECT TO CHANGE WITHOUT
NOTICE.
The latest version of this publication can be downloaded at
http://easee.support
No part of this publication may be reproduced or transmitted in any form or by
any means, electronic or mechanical, including, but not limited to, copying,
recording, retrieving data, or computer networks without the written
permission of Easee AS. Easy and all other Easee product names and slogans are
trademarks or registered trademarks of Easee AS. Easy products can be
protected by one or more patents.
All other products and services mentioned may be trademarks or service marks
of their respective owners.
Illustrations of the product and user interface are exemplary and may differ
from the actual appearance.
May 2021 – Version 1.05
© 2020 by Easee AS. All rights reserved.
AS
Grenseveien 19
4313 Sandnes, Norway
www.easee.com
References
- Easee – Shaping the future of electricity
- Easee app | Easee International
- Installer app | Easee International
- Easee – Shaping the future of electricity
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>