Atlas HiLights PS 3 Portable LED Luminaire Instruction Manual

Atlas HiLights PS 3 Portable LED Light

Product Usage Instructions

Facility

1. Read the manual carefully before installing the light.
2. Ensure proper grounding of the light.
3. Installation and maintenance should be done by professional electricians.
4. Turn off the power supply before installation or\ maintenance.
5. Ensure correct and firm installation of the product.
6. Avoid installing the light in narrow spaces.

Operation

1. Before raising the lamp post, consider installing a ZBP2000 battery pack or adding a load exceeding 38 kg on the car to prevent tipping over during use.
2. Do not attempt to replace the light source; replace the entire luminaire when the light source reaches its end of life.
3. The product can be used both indoors and outdoors.
4. To prevent strangulation risks, ensure that the flexible wiring is effectively fixed to the wall if within arm’s reach.
5. If the external flexible cable is damaged, it should be replaced by a qualified person to avoid hazards.
6. The cover should be securely held in position with at least one fixing means requiring a tool for removal.

User Guide

1. Step 1: Unfasten the straps and insert the output plug of the power box into the LED light socket.
2. Step 2: Unfold the four LED light modules, adjust the projection angle, and avoid illuminating each other on the luminous surface.
3. Step 3: Use the power switch button to turn the light on or off. Use the timer switch button to set timing functions. Use the brightness adjustment button to adjust brightness levels.

FAQ

• Q: Can I replace the light source in this fixture?
• A : No, the light source is not replaceable. The entire luminaire should be replaced when the light source reaches its end of life.
• Q: What should I do if the external cable is damaged?
• A: If the external flexible cable is damaged, it should be replaced by a qualified person to avoid hazards. Do not attempt to repair it yourself.

Safety Instruction

Notice:

1. Please read this manual carefully before installing the light:
2. The light must be grounded reliably;
3. The light must be installed and maintained by professional electricians:
4. Turn off the power supply before installing and doing maintenance:
5. Ensure products are installed correctly and firmly;
6. Do not install the light in a narrow space;
7. Before raising the lamp post, it is best to install a ZBP2000 battery pack or at least add a load exceeding 38KG on the car to prevent it from tipping over during use;
8. The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole luminaire shall be replaced ;
9. Limitation can be used both indoors and outdoors;
10. To reduce the risk of strangulation the flexible wiring connected to this luminaire shall be effectively fixed to the wall if the wiring is within arm’s reach;
11. If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similarly qualified person in order to avoid a hazard;
12. The covr shall be held securely in position by at least one fixing means requiring the use of a tool for its removal.

Electrical Specification

• Vol: 100-125 Vac 50/60Hz
• Power :480W Max 5.04A Max IP/IK: IP67 / IK10
• Power factor : 0.97
• Weight : 75
• The maximum projected area of the floodlight: is 50X50M Operating
• Temperature :-40°C ~45°C
• Wifi distance : 20M

INSTALLATION INSTRUCTION

User guide

Step 1:

1. Unfasten the straps;
2. Insert the output plug of the power box into the LED light socket

Step 2:

1. Unfold the four LED light modules and adjust the module’s projection angle, (In normal use, it is forbidden to illuminate each other on the luminous surface of the light board)

Step 3:

1. Anti-glare cover installation! install the anti-glare cover on the light in the order shown in the figure (install if necessary), the fitting slots on the anti-glare cover need to be clamped into the corresponding fitting position on the light!

Step 4:

1. Raise the stainless steel lifting rod to the required height and tighten the hand-tightened fixing screws; (In normal use, the light should be installed at a height out of reach of people)

Lowering the lamp post and retracting the LED light module
Step 1:

1. Lower the lifting rod;
2. Fold up the LED light module;

Step 2:

1. Fix the LED light module with straps or bags

Operating instructions for driver box(Steps A, B)

Step A:

1. After the mains are plugged in, the screen of the power box displays nWELCOMEn, then displays the product name and WIFI name, such as figure 1, 2; Then go to the main screen, Luminaire brightness automatically increases from low to maximum!
2. The mobile phone is connected to this WIFI, user can control the lights by the mobile phone operating interface

Step B:

1. Press this power switch button to turn off the output of the light, the light is off. Press it again to turn on the output of the light, the light is on! (figure 3)
2. Timer switch button, press this switch to start the timer function of the light。 Press this button to enter the interface of timing function. Press this key repeatedly to set the timing period to a cycle of 12 hours to 0 hour(figure 4)! Hold down this key for  seconds to disable the timing function (figure 5)

Step C:

1. Light brightness adjustment button! Press this button on the main interface to start the light brightness adjustment function, press to adjust the brightness of one gear, and switch between the 5 gears(figure 6)! Figure 6

FCC STATEMENT

Warning:
Caution:
This device complies with Part 15 of the FCC Rules
Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help. MPE Reminding

To satisfy FCC / IC RF exposure requirements, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device operation.
To ensure compliance, operations at closer than this distance is not recommended.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>