YiFeng M2 Magnetic Wireless Charging Stand User Manual
- June 9, 2024
- YiFeng
Table of Contents
YiFeng M2 Magnetic Wireless Charging Stand
Magnetic Wireless Charging Stand USER MANUAL
**Preface
**
Dear customers, thank you for purchasing our products. In order tounderstand
the product further. Please read this manual carefullybefore use.
We wish you a pleasant experience!
- lt is suggested to use 9V 2A,adapter.
Specifications
Magnetic Wireless Charging Stand
- Model: M2
- USB-C Input: 9V 2A
- Phone output: 15W Max
Please Note:
- Please remove your phone case before charging if the thickness> 5 mm, or if the phone case makes your phone size longer than 164 mm.
- Only use certified QC 3.0/PD Charging Wall Adapter to charge the device, do not plug into computer USB port or any other non-certified USB port.
- Place your qi-enabled device accurately in the wireless charging area when charging.
- a QC 3.0/PD adapter is required when charging Mobile phones can be quickly charged
- Make sure to disconnect the device from power when cleaning.
- It is normal and safe to hear a humming noise when very close to thee charger.lt means that this wireless charger is adjusting its temperature to achieve a more efficient charging speed.
- If your device can not be fully charged, this may due to high environmental temperature, please recharge after the temperature is lowered. Our charger has temperature control to safe guard your device when charging.
IMPORTANT SAFETY INSTRUCTIONS
Before Using the unit, please readthe user manual carefully
- Do not store device in high-temperature environment, including heat caused by intense sunlight or other forms of heat.
- Do not place device in fire or other excessively hot environments. Exposure to fire or temperature above 212°F (100°C) may cause explosion.
- Do not use the wireless charger in excess of its output rating. Overloading outputs above rating may result in a risk of fire or injury to persons.
- Do not expose the wireless charger to rain or snow.
- Do not modify, repair or disassemble the unity, if so, please contact the manufacturer. Switch off the wireless charger when not in use. The wireless charger will automatically switch off when disconnected from its wall charger.
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment. This
equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur ina particular
installation.If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help. FCC RF exposure statement:
The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance between 20cm the radiator your body.
IC Caution:
Radio Standards Specification RSS-Gen, issue 5 -English: This device contains
licence-exempt transmitter (s)/receiver(s) that comply with Inn ovation,
Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
RF exposure statement:
- The equipment complies with IC Radiation exposure limit set forth for uncontrolled environment.
- This equipment should be installed and operated with minimum distance 10cm between the radiator and your body.
UK:
This device was tested for uncontrolled environment operations. To comply with
RF exposure requirements, a minimum separation distance of 20cm must be
maintained between the user’s body and the product.
Declaration of Confomity
Hereby, Shenzhen Yifeng Intelligent Technology Co., Ltd. declares that the
product type M2 is in compliance with following Regulations: Radio Equipment
Regulations 2017, Electrical Equipment (Safety) Regu lations 2016 and The
Restriction of the Use of Certa in Hazardous Substances in Electrical and
Electronic Equipment Regulations 2012. The full text of the UK declaration of
conformity is available at the following internet a
ddress:https://www.YFZN.com/
EU:
This device was tested for uncontrolled environment operations.. To comply
with RF exposure requirements, a minimum separation distance of 20cm must be
maintained between the user’s body and the product.
Declaration of Conformity Hereby, Shenzhen Yifeng Intelligent Technology Co.,
Ltd.declares that the product type M2 is in compliance with Directives
2014/53/EU & 2 011/65/EU. The full text of the EU declaration of conformity is
available at the following internet address: https://www.YFZN.com/
Shenzhen Yifeng Intelligent Technology Co., Ltd. 10th Floor, Building 2,
Chaxi, Zone B, Huafeng First Science Park,Hangcheng Street, Gushu, Baoan
District, Shenzhen, China.
Thank you for choosing our product
MADE IN CHINA
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>