JONATHAN Y JYL7589A Marlowe 32.5 Inch Pendant Light Instruction Manual
- June 9, 2024
- JONATHAN Y
Table of Contents
JONATHAN Y JYL7589A Marlowe 32.5 Inch Pendant Light
WARNING WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A
LICENSED ELECTRICIAN.
WARNING *** SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE
BOX/CIRCUIT BREAKER BEFORE INSTALLATION.
INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS ANY DAMAGE OR
OBVIOUS DEFECT, DO NOT INSTALL. ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN
INSTALLED.
CARE AND MAINTENANCE
- To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the surface of the fixture.
- To clean the inside of the fixture, first disconnect power to the fixture by turning off the circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the interior surface of the fixture.
- Do not use any cleaners with chemical, solvents or harsh abrasives. Use only a dry soft cloth to dust or wipe careful
NOTICE & IMPORTANT SAFETY INSTRUCTIONS
- Please make sure that you have all parts indicated before you begin assembly of this item
- This item should be assembled on a soft surface to prevent scratching the finish during assembly
- To reduce the risk of fire, electrical shock or injury to persons or property, please follow the guideline below for safe use and installation
- The external flexible cable or cord of this luminaire cannot be replaced
- If the cord is damaged, the luminaire shall be destroyed
Part List and Hardware List
- Model#: JYL7589A
- Product Dimensions: 32.5″L X 9″W X 22.75H
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare
parts with package contents list and hardware contents list. If any part is
missing or damaged, do not attempt to assemble the product. Estimated Assembly
Time: 20 minutes.
-
Thread mounting screws (A) into the mattch holes of the mounting plate (B) , then fix the mounting plate (B) to the outlet box with machine screw (C).
-
Loosen the hex nut of the canopy (F) ,separate swivel from canopy (F).
-
connect the tubes (H) together to get desired length and fix the bottom end to nipple of the body (I) , the top end to the swivel of the canopy (F).
-
Place the swivel onto the canopy (F) ,then secure with the hex nut.
-
Make wire connections, with wire connectors (E), following the reference chart listed below.
Grounding Instructions:
-
For installation in the United States: Wrap ground wire from outlet box around green ground screw (D) on mounting plate, no less than 2″ from wire end. Tighten ground screw. If fixture is supplied with a ground wire, connect to outlet ground wire with a wire connector.
-
For installation in Canada: If fixture is supplied with ground wire, wrap ground wire around green grounding screw on mounting plate. Tighten ground screw.
-
Orient the ceiling canopy (F) so that the mounting screws (A) protruding from the mounting plate (B) go into the holes in the canopy (F) , then secure it with the provided screwed balls (G).
-
Put the glass shade (J) on socket,then fasten it by socket ring (K).
-
Install bulb (L). Be sure to use light bulb (s) with wattage no greater than specified on this fixture. Always make sure that electrical current is turned off before changing bulbs.
*Note: When parallel wire ( SPT I & SPT II ) is used. The neutral wire is square shaped and ridged and the hot wire will be round in shape and smooth. ( See Illustration on left. )
PLEASE USE ON/OFF TYPE”A” BULB MAX 40-WATT OR LED BULB MAX 9 -WATT THERE ARE LED 3PCS 4WATT BULB IN THE BOX ENJOY YOUR LAMP
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>