MOEN 10654 Double Towel Bar Installation Guide
- June 9, 2024
- Moen
Table of Contents
MOEN 10654 Double Towel Bar
Instruction
Please Contact Moen First
For Installation Help, Missing or
Replacement Parts (USA)
1-800-BUY-MOEN (1-800-289-6636)
Mon – Fri 8:00 AM to 7:00 PM, Eastern
Sat. 9:00 AM to 3:00 PM Eastern
WWW.MOEN.COM
DOUBLE TOWEL BAR
Style varies by model
HELPFUL TOOLS
For safety and ease of installation, Moen recommends the use of these helpful
tools.
Parts List
- A. Dry Wall Anchor (x4)
- B. Wood Screw (x4)
- C. Ink Stamp (x2)
- D. Set Screw (x2)
- E. Hex Wrench
- F. Mounting Plate (x2)
- G. Post (x2)
- H. Bar (x2)
- I. Level
- J. Red Pin
Determine if either of the Ink Stamp indicators line up with a stud. If a new
location is desired, see Step A1 on Page 6.
For Wood stud, proceed to Step 7A .
For Hollow wall, proceed to Step 7B . Note: Both Wood stud & Hollow wall steps
may be necessary depending on stud availability.
Drill 1/16″ holes at the ink marked stamp locations.
- Remove film backing from adhesive on included Level (I).
- Center level (I), adhesive side down, on top of the Bar (H). Press evenly to adhere.
Remove covers from Ink Stamp (C).
Assemble Bars (H) into the Posts (G).
Place Mounting Plate (F) over holes in the wall. Note: Arrow on Mounting Plate should be pointing upright and visible.
- Insert Wood Screws (B) through Mounting Plate (F).
- Secure Wood Screws (B) with a screwdriver. If Hollow wall steps are necessary, go to Step 7B. If both sets of markers are lined up with studs, go to Step 14.
Drill 5/16″ holes at the marked ink stamp locations.
-
Choose location for installation. Gently place the assembled product against the wall, ensuring bar is level. Before you compress the Ink Stamps, ensure the set screw holes are facing downward.
-
Important: Ensure Bar (H) and both Posts (G) are at a 90° angle.
-
Press and mark by pushing both Posts (G) firmly and evenly against the wall, hold for a few seconds leaving behind indicators showing you exactly where to drill.
-
Set assembled product aside.
-
Push in the center between the Dry Wall Anchor (A) ends.
-
Fold the ends of Dry Wall Anchors (A) together.
Insert the Dry Wall Anchor (A) into each hole in the wall.
Note: Refer to illustration above to ensure correct orientation.
Lightly tap Dry Wall Anchors (A) with a hammer until flush.
To actuate Dry Wall Anchors (A) Lightly tap Red Pin (J) with hammer until lower portion of Pin is engaged with the Dry Wall Anchors (A) leaving upper portion exposed.
Place Mounting Plate (F) over Dry Wall Anchors (A). Note: Arrow on Mounting Plate should be upright and visible.
-
Insert Wood Screws (B) through Mounting Plate (F).
-
Secure Wood Screws (B) with a screwdriver. Go to Step 14.
-
For both Posts (G), insert Hex Wrench (E) into Set Screw hole of Post (G).
-
Using Hex Wrench (E), loosen Set Screws (D).
-
Remove Ink Stamp (C).
Assemble Bars (H) into the Posts (G).
- Attach Posts (G) onto Mounting Bracket (F).
- Push the bottom of Posts (G) flush against the wall.
- Using Hex Wrench (E), tighten Set Screws (D). Installation complete.
Re-marking Instructions
Apply one drop of rubbing alcohol (isopropyl alcohol) to each Ink Stamp reservoir.
Apply cap, let stand for 30 sec. Ink Stamp is re-charged and ready to press and mark
Using a damp cloth, gently wash away unintended ink stamp indications from wall. Reference Step 2 on Page 3 for marking.
Troubleshooting
- If both posts don’t mount to brackets
- Remove a post and bar from the wall.
- Lightly use a hammer to tap the brackets farther away from each other. See step 16.
- Loosen the bracket screws, push the bracket away from the other, re-tighten the screw. See step 16.
- If bar is too loose on the posts
- Remove a post and bar from the wall.
- Lightly use a hammer to tap the brackets closer together. See step 16.
- Loosen the bracket screws, push the bracket closer to the other, re-tighten the screws. See step 16.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>