LS XGL-PSRA Programmable Logic Controller Installation Guide

: June 9, 2024
: LS

Table of Contents

Safety Precautions
Operating Environment
Applicable Support Software
Accessories and Cable Specifications
Parts Name and Dimension (mm)
Installing / Removing Modules
Wiring
Warranty
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

LS XGL-PSRA Programmable Logic Controller Installation Guide

LS XGL-PSRA Programmable Logic Controller Installation
Guide

This installation guide provides simple function information or PLC control. Please read carefully this data sheet and manuals before using products. Especially read precautions then handle the products properly.

Safety Precautions

■ Meaning of warning and caution label

WARNING

WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury

WARNING

CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
It may also be used to alert against unsafe practices

WARNING

Do not contact the terminals while the power is applied.
Be sure there are no foreign metallic matters.
Do not manipulate the battery(charge, disassemble, hitting, short, soldering).

CAUTION

Be sure to check the rated voltage and terminal arrangement before wiring
When wiring, tighten the screw of terminal block with the specified torque range
Do not install the flammable things on surroundings
Do not use the PLC in the environment of direct vibration
Except expert service staff, do not disassemble or fix or modify the product
Use the PLC in an environment that meets the general specifications contained in this datasheet.
Be sure that external load does not exceed the rating of output module.
When disposing of PLC and battery, treat it as industrial waste.
I/O signal or communication line shall be wired at least 100mm away from a highvoltage cable or power line.

Operating Environment

■ To install, observe the below conditions.

LS XGL-PSRA Programmable Logic Controller - Operating
Environment

Applicable Support Software

For system configuration, the following version is necessary.

XGI CPU : V3.9 or above
XGK CPU : V4.5 or above
XGR CPU : V2.6 or above
XG5000 Software : V4.0 or above

Accessories and Cable Specifications

Check Profibus Connector contained in the box

Usage : Profibus Communication Connector
Item : GPL-CON

When using Pnet communication, shielded twisted pair cable shall be used with consideration of communication distance and speed.

Manufacturer : Belden or the maker of equivalent material specification below
Cable Specification

LS XGL-PSRA Programmable Logic Controller - When using Pnet communication,
shielded twisted pair cable shall be used with
consideration

Parts Name and Dimension (mm)

This is front part of the Module. Refer to each name when operating the system. For more information, refer to user’s manual.

$LS XGL-PSRA Programmable Logic Controller - Parts Name and Dimension $mm$$

■ LED details

LS XGL-PSRA Programmable Logic Controller - LED
details

Installing / Removing Modules

■ Here describes the method to attach each module to the base or remove it.

LS XGL-PSRA Programmable Logic Controller - Installing Removing
Modules

Installing module
① Insert a fixed projection of the lower part Of PLC into the module fixed hole of base
② Slide the upper part of module to fix to the base, and then fit it to the base by using the module fixed screw.
③ Pull the upper part of module to check if it is installed to the base completely.
Removing module
① Loosen the fixed screws of the upper part of module from the base
② By pressing the hook, pull the upper part of module from the axis of the lower part of module
③ By lifting the module upward, remove the loading lever of module from the fixing hole

Wiring

Connector structure and wiring method

Input line: green line is connected to A1, red line is connected to B1
Output line: green line is connected to A2, red line is connected to B2
Connect shield to clamp of shield
In case of installing the connector at terminal, install the cable at A1, B1
For more information about wiring, refer to user manual.

Warranty

Warranty period 18 months after the production date.
Scope of Warranty 18-month warranty is available except:

The troubles caused by improper condition, environment or treatment except the instructions of LS ELECTRIC.
The troubles caused by external devices
The troubles caused by remodeling or repairing based on the user’s own discretion.
The troubles caused by improper usage of the product
The troubles caused by the reason which exceeded the expectation from science and technology level when LS ELECTRIC manufactured the product
The troubles caused by natural disaster

LS XGL-PSRA Programmable Logic Controller - Scope of
Warranty