LIGHTPRO 144A Transformer Timer and Light Sensor User Manual

LIGHTPRO 144A Transformer Timer and Light Sensor User Manual

Introduction

Thank you for purchasing the Lightpro Transformer + Timer / Sensor. This document contains the required information for correct, efficient and safe use of the product.
Read the information in this manual carefully before using the product. Keep this manual near the product for  consultation in the future.

SPECIFICATIONS

• Product : Lightpro Transformer + Timer / Sensor
• Article number : Transformer 60W – 144A Transformer 100W – 145A
• Dimensions (H x W x L) : 162 x 108 x 91 mm
• Protection class : IP44
• Ambient temperature : -20 °C tot 50 °C
• Cable length : 2m

PACKAGING CONTENT

1. Transformator
2. Screw
3. Plug
4. Cable lugs
5. Light sensor

60W transformer

Input: 230V AC 50HZ 70VA
Output: 12V AC MAX 60VA

100W transformer

Input: 230V AC 50HZ 120VA
Output: 12V AC MAX 100VA

Check if all parts are present in the packaging. For questions about parts, service, and any complaints or other remarks, you can always contact us.
E-mail: info@lightpro.nl.

INSTALLATION

Mount the transformer with the setting knob pointing downwards < Fig. A>. Attach the transformer to a wall, partition or pole (at least 50 cm above the floor). The transformer is equipped with a light sensor and a time switch.

Light sensor

< Fig. B > The light sensor is fitted with a 2 metre long cable. The cable with sensor can be disconnected, for instance to be led through a hole in the wall. The light sensor <Fig. B1> is mounted with a clip <Fig. B2>. This clip must be attached to a wall, pole or similar. We advise to install the light sensor vertically (facing upward). Mount the sensor to the clip and connect the sensor to the transformer <Fig. A2>.

Mount the light sensor in such a way that it cannot be influenced by light from the outside environment (car headlights, street lighting or the own garden lighting, etc.). Ensure that only day and night natural light can influence the functioning of the sensor.

Should the 2 metre cable not suffice, then the sensor cable can be lengthened by use of an extension cord.

Setting the transformer

The transformer can be set in different ways. The light sensor <Fig. B1> works in combination with the time switch <Fig. C>. The lighting switches on at sunset and switches off after the set number of hours or automatically at sunrise.

• “Off” switches the light sensor off, the transformer switches off completely
• “On” switches the light sensor on, the transformer is on continuously (this may be necessary for testing during day hours)
• “Auto” switches the transformer on at dusk, the transformer switches off at sunrise
• “4H” switches the transformer on at dusk, the transformer switches off automatically after 4 hours
• “6H” switches the transformer on at dusk, the transformer switches off automatically after 6 hours
• “8H” switches the transformer on at dusk, the transformer switches off automatically after 8 hours

Location of the light/dark sensor

The light sensor might be influenced by artificial light. Artificial light is light from the surroundings, such as light from the own home, light from street lights and cars, but also from other outside lights, for instance a wall light. The sensor does not signal the “dusk” in case artificial light is present and will therefore not activate the transformer. Test the sensor by covering it, using the included cap <Fig. B1>. After 45 seconds, the transformer should be activated, turning on the lighting

First check if all lights are functioning before deciding to bury the cable in the ground.

THE SYSTEM

The Lightpro cable system consists of a 12 volt cable (50, 100 or 200 metres) and connectors. When connecting the Lightpro light fixtures, you must use the Lightpro 12 volt cable in combination with the 12 volt Lightpro transformer. Apply this product within the 12 Volt Lightpro system, otherwise the warranty will become invalid.

The European standards do not require the 12 volt cable to be buried. In order to prevent damage to the cable, for instance while hoeing, we recommend to bury the cable at least 20 cm deep.

On the main cable (article numbers 050C14, 100C14 or 200C14) connectors are connected to link the lighting or to make branches.

Connector 137A (type F, female)

< Fig. D1> This connector is included with every fixture as a standard and is supposed to be connected to the 12 Volts cable. The fixture plug or the male connector type M is connected to this connection. Connect the connector to the cable by means of a simple twist.

Make sure that the 12 volt cable is clean before a connector is connected, to prevent poor contact.

Connector 138 A (type M, male)

<Fig. D2+D3> This male connector is attached to the 12 volt cable in order to be able to connect the cable to the female connector (137A, type F), with the aim to make a branch.

Connector 143A (type Y, connection to transformer)

<Fig. D4+D5> This male connector is attached to the 12 volt cable in order to be able to connect the cable to the transformer. The connector has cable lugs on one side that can be connected to the clamps of the transformer.

CABLE

LAYING A CABLE IN THE GARDEN

Lay the main cable through the entire garden. When laying the cable, keep the (planned) paving in mind, ensure that later on lighting can be fitted in any position. If possible, apply a thin PVC tube under the paving, where, later on, a cable can be led through.

Should the distance between the 12 volt cable and the fixture plug still be too long, then a (1 m or 3 m) extension cord can be used to connect the fixture. Another way of providing a different part of the garden with main cable is to make a branch on the main cable which is connected to the transformer.

We recommend a cable length of 70 metres at most between the transformer and the light fixtures <Fig. E1>.

Making a branch on the 12 volt cable