Yifeng DT1000A Rechargeable and Waterproof Remote Dog Training Collar User Guide

Yifeng DT1000A Rechargeable and Waterproof Remote Dog Training Collar

Features

1. Rechargeable Remote Transmitter
2. Rechargeable and Water poof Receiving Collar
3. 1000 feet remote control range between Remote Transmitter and Receiving Collar.
4. Beep Mode activates a correcting tone on the Receiving Collar
5. Adjustable vibration intensity level from 1-99 level
6.  Adjustable static shock intensity level from 1-99 level (optional)
7. Power saving modes
   • The Receiving Collar will go into Standby Mode if ifs idle for more than 5 mins. Any movements will activate the Receiving Collar.
8. The Transmitter will go into Standby Mode (0 will be light off with 30S, ,..,will be light off with 1min) Press [lJ \\f\\ ,- button to re-activate it from Standby mode.

How does the Rechargeable and Waterproof Dog Training Collar Work
The Rechargeable and Waterproof Training Collar has been proven to be a safe, comfortable, and effective training system for all dogs weighing over 15Ibs.This system allows you to control your dog within a range up to 1000 feet. At the press of a button. the Remote Transmitter sends signal to the Receiving Collar and activates a Beep, a Vibration or a Static Shock correction output .By using the Training Collar properly, you can correct much of your dog’s undesired behavior and teach basic and advanced obedience commands.

Thanks for choosing the Rechargeable and Waterproof Remote Dog Training Collar. Our mission is to provide you with the safe tools and techniques to train your dog.

Important:
the Training Collar has an effective range up to 1000 feet Hold the Remote Transmitter horizontally away from your body to achieve the optimum range. Terrain features, weather, vegetation, transmission from other radio devices and other factors may affect the range of the Remote Transmitter

Precautions
DO NOT use this product for aggressive dogs or vicious animals.

Risk of skin damage.
it’s important to fit the collar properly. A collar that is fitted too tightly or wear for too long may harm your dog’s skin.This condition, which ranges from redness to pressure ulcers, is commonly known as bed sores.

CAUTION

• Do not let your dog wear the collar for more than 12 hours per 24-hour period

• If possible, gently reposition the collar on your dog’s neck every 1 or 2 hours Never attach a lead to the Receiver Collar. as this would cause excessive pressure on the contact points.
  When using a separate collar to connect a leash. please ensure that it does not put excessive pressure on the electronic collar.

• Examine your dog’s neck daily for scans of chafing or soreness

• If a rash or sore is found. stop using the collar till the injured skin has been healed.

• If the condition persists for more than 48 hours. consult your veterinarian

• If possible, please use the Beep Mode or Vibration Mode at first, then can try Static shock function.

• Please ensure that you charge both the Receiving collar and the Remote Transmitter before using!
  To extend the battery life of this product, please charge them per month if you do not intend to use it for a long period of time.

Components

How to change the contact point to the Receiver Collar

Key Definition

1. LED screen
2. Adjustment Button
3. Shock button
4. Vibration button
5. Beep button
6. Channel button
7. Lock key switch
8. Charging port

• 1-99 level
• Beep mode
• Vibration mode
• Static shock mode 1
• T Signal mark
• Full battery
• :& Low battery
• Channel 1
• Channel 2
• Channel 3
• Channel 4

1. LED Screen

Beep mode: When this symbol [lJ is displayed, press the [lJ button to activate a Beep tone on the Receiving Collar.
Vibration Mode: when this symbol “‘ is displayed, press the u button to activate Vibration. Rotate the knob to adjust the intensity of the vibration from 1 to 99. Static Shock Mode: when this symbol • is displayed, press the 4’ button to activate Static Shock. Rotate the knob to adjust the intensity of the shock from 1 to 99. Signal: when this symbol T is displayed, means the transmitter is launching signal. Full battery: when this symbol m is display when charging, means the battery is in full Low battery: when this symbol .::S:: is display, means the transmitter is in low battery and need to be recharged Key lock:

1. when this symbol is display, mean the transmitter is under key lock. Channel 1/4:select 1/4 channel to encode the Receiving Collar 1/4
2. Adjustment Button: adjustment button to adjust the Intensity of the Vibration or Shock from the lowest level 1 to the highest level 99 /4/5.ShockNibration/Beep button: press this button to launch the correct signal
3. Channel button: press this button to change between the 1-4
4. Receiving Collar (if applicable)
5. Key Lock switch: push up/down the switch to lock/unlock the key function.
6. Charging port: plug the USB charging cable into the port to charge the

Remote Transmitter

• Lithium battery: 3.7V 300mAh for the Remote Transmitter
  3.7V 250mAh for the Receiving Collar

• Operating Frequency: RF433 MHZ

• Contact points: 2 pairs of metal contacts to be chosen to suit the length of your dog’s hair

• Mini Spanner: a tool to screw/unscrew contact points on the electrodes

• Contact Points; Deliver vibration / safe static correction

Operation Guide

Preparing the Remote Transmitter Charging the Remote Transmitter

1. Plug the USB Charging Cable into the Charging port

2. Plug the Adapter into a standard outlet

3. The number in LCD screen will be lighting circularly when charging

4. The LED screen will show

   • once its fully charged with 2.5 hours. Remove the USB Charging Cable.
     Low battery indicator: The LED screen will show

   • and flash 30seconds,then transmitter will be turned off automatically.

How to use the Remote Transmitter

1. Push down the key lock switch, the LED screen light
2. Press Shock Nitration /Beep button, the LED screen will display ( “‘,) which mean the corresponding mode is activated
3. Rotating to set the intensity of shock or vibration
4. Select different channels for 1-4Receiving Collars

Power Saving Mode: the Remote Transmitter will ans into Standby Mode if it is idle for 1 min. The LED screen on the Remote Transmitter will not display anything in this case(will be light off with 30s “‘ , will be light off with 1min), press any button to re-activate it.
Lock Key function: Push un the lock switch the will flash for 6 seconds then it goes into key lock mode and it won’t be activated any more, the ( ) will. flash for 6 seconds again if any button be pressed. Push down the lock switch, the Transmitter will on work

Preparing the Receiving Collars Charging the Receiving Collar

1. Remove the rubber cover and plug the USB Charging Cable into the charging port.
2. Plug the Adapter into a standard outlet.

Note: Most of the Rechargeable and Waterproof Training Collars have already been encoded before leaving the factory. If so , just press any button on the transmitter to activate, then press the with 1 sec on receiving collar to turn on it, after that, you can test the function refer to

Step 4
Step Testing the Rechargeable and Waterproof Training Collar:

Testing the Static Shock+ Function The static impulse generated by the Receiving Collar cannot be seen _by naked eyes. Test whether the Static Shock Function wore<s byus1ngthefollow1ngprocedure.

• Remove the Test Light from the package and connect it to the contact points on the receiving collar
• Press the+ button on Remote Transmitter to launch Static Shock signal, if the Test Light flashes, the Static Shock Function is working correctly.
• The intensity of the Static Shock can be adjusted by rotating the rotary knob from level 1-99.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>