MEAN WELL LPV-100 100W Single Output Switching Power Supply User Manual

: June 4, 2024
: MEAN WELL

Table of Contents

MEAN WELL LPV-100 100W Single Output Switching Power Supply
Features
GTIN CODE
SPECIFICATION
Mechanical Specification
Recommend Mounting
Block Diagram
Derating Curve
Static Characteristics
Read User Manual Online (PDF format)
Download This Manual (PDF format)

MEAN WELL LPV-100 100W Single Output Switching Power Supply

MEAN-WELL-LPV-100-100W-Single-Output-Switching-Power-Supply-
product

Features

Constant voltage design
Universal AC input/ Full range
Fully encapsulated with IP67 level (Note.7)
Withstand 300VAC surge input for 5 seconds
Protections: Short circuit/ Overload/Over voltage
Fully isolated plastic case
Cooling by free air convection
100% full load burn-in test
Low cost, high reliability
Suitable for LED-related fixtures or appliances (such as LED Decoration or Advertisement devices) (Note.11)
2 years warranty

GTIN CODE

MW Search: https://www.meanwell.com/serviceGTIN.aspx

SPECIFICATION

MODEL| LPV-100-5| LPV-100-12| LPV-100-15| LPV-100-24| LPV-100-36| LPV-100-48
---|---|---|---|---|---|---

OUTPUT

| DC VOLTAGE| 5V| 12V| 15V| 24V| 36V| 48V
RATED CURRENT| 12A| 8.5A| 6.7A| 4.2A| 2.8A| 2.1A
CURRENT RANGE| 0 ~ 12A| 0 ~ 8.5A| 0 ~ 6.7A| 0 ~ 4.2A| 0 ~ 2.8A| 0 ~ 2.1A
RATED POWER| 60W| 102W| 100.5W| 100.8W| 100.8W| 100.8W
RIPPLE & NOISE (max.) **Note.2| 80mVp-p| 120mVp-p| 120mVp-p| 150mVp-p| 150mVp-p| 150mVp-p
VOLTAGE TOLERANCE Note.3| ±8.0%| ±5.0%
LINE REGULATION| ±1.0%
LOAD REGULATION| ±6.0%| ±2.0%
SETUP, RISE TIME| Note.6| 2000ms, 25ms / 230VAC 2000ms, 25ms / 115VAC
HOLD UP TIME (Typ.)**| 50ms/230VAC 14ms/115VAC at full load

INPUT

PROTECTION

| OVERLOAD| 110 ~ 150% rated output power
Protection type: Hiccup mode, recovers automatically after the fault condition is removed
OVERVOLTAGE| 5.75 ~ 6.75V| 13.8 ~ 16.2V| 17.25 ~ 20.25V| 27.6 ~ 32.4V| 41.4 ~ 48.6V| 55.2 ~ 64.8V
Protection type: Shut down o/p voltage, re-power on to recover

ENVIRONMENT

| WORKING TEMP.| -25 ~ +70℃ (Refer to “Derating Curve”)
WORKING HUMIDITY| 20 ~ 90% RH non-condensing
STORAGE TEMP., HUMIDITY| -40 ~ +80℃, 10 ~ 95% RH
TEMP. COEFFICIENT| ±0.03%/℃ (0 ~ 50℃)
VIBRATION| 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes

SAFETY & EMC

| SAFETY STANDARDS| UL8750,CSA C22.2 No 250.13-12,UL879,CSA C22.2 No.207-M89,BIS IS15885(for LPV-100-12,LPV-100-24 only), EAC TP TC 004,IP67, IEC62368-1 , BS EN/EN62368-1 approved
WITHSTAND VOLTAGE| I/P-O/P:3KVAC
ISOLATION RESISTANCE| I/P-O/P:>100M Ohms / 500VDC / 25℃/ 70% RH
EMC EMISSION| Compliance to BS EN/EN55032 (CISPR32) Class B, BS EN/EN61000-3-2 Class A(≤80% load), BS EN/EN61000-3-3, EAC TP TC 020
EMC IMMUNITY| Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11; BS EN/EN55035, light industry level, EAC TP TC 020

OTHERS

| MTBF| 4497.1K hrs min. Telcordia SR-332 (Bellcore) ;| 681.6Khrs min.| MIL-HDBK-217F (25℃)|
DIMENSION| 1905237mm (LWH)
PACKING| 0.63Kg;20pcs/13.6Kg/0.55CUFT
NOTE| 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load, and 25C of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12″ twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance: includes set up tolerance, line regulation, and load regulation.
4. Derating may be needed under low input voltage. Please check the static characteristics for more details.
5. The power supply is considered as a component that will be operated in combination with the final equipment. Since EMC performance will be affected by the
complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
6. Length of set up time is measured at first cold start. Tuning ON/OFF the power supply may lead to an increase in the setup time.
7. Suitable for indoor use or outdoor use without direct sunlight exposure.
8. The ambient temperature derating of 3.5 C/1000m with fanless models and of 5 C/1000m with fan models for operating altitudes higher than 2000m(6500ft)
9. Products sourced from the Americas regions may not have the TUVBIS/CCC logo. Please contact your MEAN WELL sales for more information.
10. For any application note and IP waterproof function installation caution, please refer to our user manual before using.
https://www.meanwell.com/Upload/PDF/LED_EN.pdf
11. This product is not intended for LED lighting luminaire applications in the EU. (In the EU the LPFNPF/XLG series are recommended.)
product Liability Disclaimer: For detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx