DETEX 105665 Pacific Lock Instruction Manual

: June 4, 2024
: DETEX

Table of Contents

2 and #3 Phillips Screw Drivers

105665 Pacific Lock
Instruction Manual
104870 January 15, 2021

Detex Corporation, 302 Detex Drive, New Braunfels, Texas 78130-3045 830-629-2900 / 800-729-3839
Fax 800-653-3839 / Text photos only: 830-481-6433 / INTERNET: www.detex.com
INSTALLATION INSTRUCTIONS FOR 08D x 2W, 09D x 2W and 14D x 2W
TRIM drawing 105665: 08D x 2W drawing
105666: 09D x 2W drawing 105668: 14D x 2W
Should you have a Question/Problem with your Detex device please call Detex
Technical Support from the job site at 1-800-729-3839 and choose option 2 on our menu.
Please do not return the product to the distributor.

Owner’s Copy
For WARRANTY information, scan the code below or go to www.detex.com/warranty
For device installation videos, scan the code below or go to www.detex.com/videos

LHR ASSEMBLIES SHOWN Your particular part or configuration may not be shown: Contact Detex technical support at 800-729-3839 (option 2)
Tools Required:
Safety Glasses Power Drill
Tape Measure Level Pencil
Center Punch Hammer

2 and #3 Phillips Screw Drivers

Drill bits: 5/16″ 1/2″ 3/4″
FOR ITEM 26 “-X” REFERS TO
KEY CODE AA-KK

PARTS BREAKDOWN

Item	P/N	QTY	Description
1	106264-7	1	LEVER ASSY, 0, 626
106264-14	LEVER ASSY. 0, 693
106264-15	LEVER ASSY. 0, 695
101376-7	LEVER ASSY. S, 626
101376-14	LEVER ASSY. S, 693
101376-15	LEVER ASSY. S. 695
101375-7	LEVER ASSY. U. 626
101375-14	LEVER ASSY. U. 693
101375-15	LEVER ASSY. U. 695
101374-7	LEVER ASSY, T, 626
101374-14	LEVER ASSY. T. 693
101374-15	LEVER ASSY. T. 695
2	106603	2	WASHER. FLAT. 1″x0.02 THK (J LEVER ONLY)
100851	1	WASHER. FLAT. 1″x0.06 THK (ALL EXCEPT J LEVER)
3	105664-9	1	ESCUTCHEON ASSY. O8Dx2W / 09Wx2W. BP2. 630 FINISH
105669-9	ESCUTCHEON ASSY. 14Dx2W. BP2. 630 FINISH
4	100771	1	STOP. ROTATIONAL
6	104220	2	STANDOFF. HEX. BP2, EU
7	100775	1	WASHER. FLAT
8	103047	1	CLUTCH SPRING
9	103043	1	BOTTOM GEAR. WIDE
10	103044	1	TORQUE PLATE. WIDE
11	103994	1	KEY. SHEAR PIN. STEEL
12	100821	1	WASHER CLUTCH
13	100773	1	FLAT SPRING LOCKING (08D function only)
101997	SPRING. COMPRESSION (09D function only)
14	102536-1	1	SCREW. 10-24. CUSTOM
15	100766	1	SPRING. RETURN
16	101509	1	SPRING. RETURN. HELPER
17	101436	1	RACK ASSEMBLY
18	100753	1	COVER PLATE
19	PP-5378-106	2	SCREW. MACH, 8-32 x 3/8 PPH
20	PP-5367-108	1	SCREW. MACH. 6-32 x 1/2 PPH
21	100762	1	TOP GEAR
22	101993	1	LOCK SLIDE (08D / 09D only)
23	104214	1	ADAPTER PLATE. BP2. EU
24	100572-9	1	CYLINDER COLLAR. SHORT
100752-9	CYLINDER COLLAR. TALL
25	105964	1	WASHER. WAVE
26	103800-626	1	CYLINDER HOUSING. SFIC. MORTISE. 7 PIN. CHROME
102281-7-X	CYLINDER. MORTISE. 5 PIN. CHROME
27	100754	1	PLATE. CYLINDER POSITION
28	100783	1	NUT. HEXAGON. CYLINDER
29	101478	1	SHAFT EXTENSION ASSEMBLY
30	104224-14	1	LOCKNUT. 1/4-20. NYLON INSERT
31	102264-2	2	SCREW. 1/4-20 x 3/8 PFH. UNDERCUT

STEP 1: PREP TRIM

Install tailpiece & cylinder (14 function requires no cylinder)
NOTE:

Mortise cylinder NOT supplied with trim, but can be ordered separately.
Trim handing is field reversible.
6-pin cylinder installation shown.

Follow steps A through C in order:

STEP 2: PREP DOOR

STEP 3: INSTALL TRIM

TRIM INSTALLATION COMPLETE
Continue installation using device instructions

CHANGE LEVER HANDING

A. Remove tailpiece extension assembly screw. (Remove tailpiece extension assembly if necessary.
B. Remove lower stand-off and stop plate.
C. WARNING: Springs under pressure! Remove the spring retaining plate. Carefully remove the springs.
D. Switch the lock spring to the opposite side (for the 09 function only).
E. Remove top gear.
F. Loosen the clutch center screw for approximately two (2) turns. Bend the locking tab back to disengage with a notch.
G. Slide the locking bar away from the rack (not necessary for 14 functions). Remove the rack while rotating the lever.
H. Continue rotating the lever to the opposite side.
I. Rotate the lever to the position shown. Partially engage the rack and the clutch gear on the opposite side.
J. Rotate the lever until the rack is completely seated.
K. Insert the top gear.
L. Add permanent thread locking adhesive and tighten the clutch center screw. Bend the tab over the screw notch so that screw cannot turn.
M. Warning: Springs under pressure! Install the springs. Hold the lever in the down position, firmly compressing the springs in place.
N. While holding the lever in the down position, replace the spring retaining plate and fasten the two (2) screws.
O. Reverse the stop plate and fasten the stand-off.
P. Replace tailpiece extension assembly (if removed) and assembly screw.