DETEX 14D Advantex Outside Lever Trim Instruction Manual

June 4, 2024
DETEX

DETEX 14D Advantex Outside Lever Trim

LHR ASSEMBLIES SHOWN

(RHR assemblies opposite)

Your particular part or configuration may not be shown: Contact Detex technical support at 800-729-3839 (option 2)

PARTS BREAKDOWN

Item| P/N| QTY| Description

1

| 106264-7|

1

| LEVER ASSY, Q, 626
106264-14| LEVER ASSY, Q, 693
106264-15| LEVER ASSY, Q, 695
101376-7| LEVER ASSY, S, 626
101376-14| LEVER ASSY, S, 693
101376-15| LEVER ASSY, S, 695
101375-7| LEVER ASSY, U, 626
101375-14| LEVER ASSY, U, 693
101375-15| LEVER ASSY, U, 695
101374-7| LEVER ASSY, T, 626
101374-14| LEVER ASSY, T, 693
101374-15| LEVER ASSY, T, 695
2| 106603| 2| WASHER, FLAT, 1″x0.02 THK (J LEVER ONLY)
100851| 1| WASHER, FLAT, 1″x0.06 THK (ALL EXCEPT J LEVER)
3| 101373-9| 1| ESCUTCHEON ASSY, 08W / 09W, BP1, 630 FINISH
101459-9| ESCUTCHEON ASSY, 14W, BP1, 630 FINISH
4| 100771| 1| STOP, ROTATIONAL
5| PP-5305-108| 1| SCREW, MACH, 10-24 X 1/2 PFH
6| 100777| 4| STANDOFF, HEX
7| 100775| 1| WASHER, FLAT
8| 103047| 1| CLUTCH SPRING
9| 103043| 1| BOTTOM GEAR, WIDE
10| 103044| 1| TORQUE PLATE, WIDE
11| 103994| 1| KEY, SHEAR PIN, STEEL
12| 100821| 1| WASHER CLUTCH
13| 100773| 1| FLAT SPRING LOCKING (08 function only)
101997| SPRING, COMPRESSION (09 function only)
14| 102536-1| 1| SCREW, 10-24, CUSTOM
15| 100766| 1| SPRING, RETURN
16| 101509| 1| SPRING, RETURN, HELPER
17| 101436| 1| RACK ASSEMBLY
18| 100753| 1| COVER PLATE
19| PP-5378-106| 2| SCREW, MACH, 8-32 x 3/8 PPH
20| PP-5367-108| 1| SCREW, MACH, 6-32 x 1/2 PPH
21| 100762| 1| TOP GEAR
22| 101993| 1| LOCK SLIDE
23KIT| 105673-1| 1| LEVER TRIM HARDWARE KIT, RIM/SVR
105673-3| LEVER TRIM HARDWARE KIT, CVR
23A| 100754| 1| PLATE, CYLINDER POSITION
23B| 100783| 1| NUT, HEXAGON, CYLINDER
23C| 101478|

1

1

| SHAFT EXTENSION ASSEMBLY
106694| TAILPIECE ASSEMBLY, D TRIM, CVR UNIVERSAL
24| 100572-9| CYLINDER COLLAR, SHORT
100752-9| CYLINDER COLLAR, TALL
25| 105964| 1| WASHER, WAVE
26| 103800-626| 1| CYLINDER HOUSING, SFIC, MORTISE, 7 PIN, CHROME
102281-7-X| CYLINDER, MORTISE, 5 PIN, CHROME

Tools Required:

  • Safety Glasses
  • Power Drill
  • Tape Measure
  • Level
  • Pencil
  • Center Punch
  • Hammer
  • 2 and 3 Phillips Screw Drivers
  • Drill bits:
    • 5/16″
    • 1/2″
    • 3/4
**STEP 1: PREP TRIM

DETEX 14D Advantex Outside Lever Trim fig
\(2\)**

Install tailpiece & cylinder
(14 function requires no cylinder)

NOTE:

  • Mortise cylinder NOT supplied with trim, but can be ordered separately.
  • Trim handing is field reversible.
  • 6-pin cylinder installation shown
STEP 2: PREP DOOR

DETEX 14D Advantex Outside Lever Trim fig
\(3\)

Mark and drill holes
(LHR installation shown, reverse for RHR)

STEP 3: INSTALL TRIM

DETEX 14D Advantex Outside Lever Trim fig
\(4\)

CHANGE LEVER HANDING (if required)

  • Remove tailpiece extension assembly screw. Remove tailpiece extension assembly if already installed.
  • Remove stop plate.
  • Warning: Springs under pressure! Remove the spring retaining plate and carefully remove the springs.
  • Switch the lock spring to the opposite side (for 09 function only).
  • Remove top gear.
  • Loosen the clutch center screw for approximately two (2) turns. Bend the locking tab back to disengage with a notch.
  • Slide the locking bar away from the rack (not necessary for 14 functions). Remove the rack while rotating the lever.
  • Continue rotating the lever to the opposite side.
  • Rotate the lever to the position shown. Partially engage the rack and the clutch gear on the opposite side.
  • Rotate the lever until the rack is completely seated.
  • Insert the top gear.
  • Add permanent thread locking adhesive and tighten the clutch center screw. Bend tab over the screw notch so the screw cannot turn.
  • WARNING: Springs under pressure! Install the springs. Hold the lever in the down position, firmly compressing the springs in place.
  • While holding the lever in the down position, replace the spring retaining plate and fasten the two (2) screws.
  • Reverse the stop plate and fasten the screw.
  • Replace the tailpiece extension and screw

Should you have a Question/Problem with your Detex device please call Detex Technical Support from job site at 1-800-729-3839 and choose option 2 on our menu. Please do not return the product to the distributor.

For WARRANTY information, scan code below or go to www.detex.com/warranty

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals