DETEX 03WS Outside Lever Trim Device Instructions

June 4, 2024
DETEX

DETEX-logo

Detex Corporation, 302 Detex Drive, New Braunfels, Texas 78130 (830)629-2900 /1-800-729-3839 /FAX(830)620-6711
Addendum to 03WS (Outside Lever Trim) Instructions

This addendum is for use on 2″ narrow stile glass doors using the 03WS Trim Devices.
CAUTION: If you are using 03WS trim on a 2″ narrow stile glass door, DO NOT USE THE PROVIDED STRIKE LOCATOR. (All other narrow trims can use the narrow strike locator, provided in the Strike Kit.)
To install 03WS device without a strike locator:

INSIDE DOOR FACE:

  1. Mark a line 1″ from the edge of the door (See Fig. 1).
    DETEX 03WS Outside Lever Trim Device-

  2. Block door shut. (Perform steps 3 through 8 inside the door.)

  3. Detex recommends the device be mounted 40″ above the finished floor. Mark the 40″ centerline of the device across the door and frame. (See Fig. 2)
    DETEX 03WS Outside Lever Trim Device-Fig 2

  4. Place back plate on door stile. Use the 1″ line and center holes (a & e) on back plate.
    Align cam center to mark “d” for proper height. (See Fig. 3)
    DETEX 03WS Outside Lever Trim Device-Fig 3.

  5. Mark and center punch 5 holes “a” “d” & “e”.

  6. Slide the strike against the blocked door. (See Fig. 4)
    DETEX 03WS Outside Lever Trim Device-Fig4

  7. Mark and center punch 2 strike holes. (See Fig. 5)
    DETEX 03WS Outside Lever Trim Device-Fig5

  8. Drill one pilot hole “e” thru the door (See Fig. 5).
    NOTE: DRILL STRAIGHT AND LEVEL
    OUTSIDE DOOR FACE:

  9. Place the back plate on the door (use it as a template).

  10. Center the back plate on pilot hole “e” and align the back plate vertically.

  11. Mark the cam center “d”. Mark and center punch the other hole “e”.

  12. Make a new mark 1/4″ higher than the cam center (just marked). This will be the mark for the 1 3/4″ outside cylinder hole “f”.

  13. Drill a pilot hole through the door for “e” and “f”.
    NOTE: DRILL STRAIGHT AND LEVEL

  14. Using a 1 3/4″ hole saw, cut through the outside door face at “f”.
    NOTE: USE EXTREME CAUTION WHEN DRILLING 1 3/4″ HOLE.
    TIGHT TOLERANCE, NO MARGIN FOR ERROR.
    INSIDE DOOR FACE:

  15. Drill 3/4″ hole through the inside door face at “d”.

  16. Using a 5/16″ drill bit, enlarge the two holes “e” through the door.

  17. See Fig. T6. Drill back plate mounting holes “a” per chart. CAUTION: Holes “a” are drilled inside only.

Backplate Mounting Holes “a” Trim Holes “e”
1/4-20 Machine Screw #14 Wood Screw
Screws Door Thickness

7

OR
13/64
1 1/4-20| 3/16″| # 7
OR
13/64| 5/16| 1 3/8″| 2″
1 3/4″| 2 1/4″
2″ or 2 1/4″| * 39”

**Fig. T6

  • Cut to length**

Go to Instructions P/N 101257 (03WS Installation Instructions)

Complete Page 2 “Preparing the Trim”.
Skip Page 3
Complete Page 4 “Assembling the Outside Trim…..”
Resume with Panic Hardware Instruction #15.

INS-101269
101269 November 19, 2007

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals