DETEX 03CM 626 Trim Charlotte Mort Nl 626 Advantex 30 Series Night Latch Pull Instruction Manual
- June 4, 2024
- DETEX
Table of Contents
03CM 626 Trim Charlotte Mort Nl 626 Advantex 30 Series Night Latch Pull
Instruction Manual
03CM 626 Trim Charlotte Mort Nl 626 Advantex 30 Series Night Latch Pull
| ITEM | PART NO. | QTY | DESCRIPTION |
|---|---|---|---|
| 1 | 103296-9 | 1 | TRIM PLATE, 03WM, BRUSHED STAINLESS STEEL FINISH (630) |
| 2 | 102281-X | 1 | CYLINDER, MORTISE, 5 PIN |
| 3 | 100752-X | 1 | CYLINDER COLLAR, TALL |
| 4 | 102235-9 | 1 | PULL, 03C |
| 5 | 102264-1 | 1 | SCREW, MACH, 1/4-20 X 1/2″ UNDERCUT, PFH |
| 6 | 102271-136 | 1 | SCREW, MACH, 1/4-20 X 2-1/4″, PFH, STAINLESS STEEL |
| 102271-144 | 1 | SCREW, MACH, 1/4-20 X 2-3/4″, PFH, STAINLESS STEEL | |
| 7 | 102272-2 | 1 | WASHER, #14, FINISHED, STAINLESS STEEL |
STEP 1:
PREP DOOR
MARK & DRILL HOLES – TRIM SIDE:
Use a plastic template to mark TRIM holes (LHR shown)
NOTE : The height from the finished floor to the trim/device centerline
that Detex recommends is 40″. If unsure of trim/device centerline location,
use the method below and at right to determine the correct trim location.
MARK HOLES:
Align the plastic template LOCK CENTERLINE with the mark previously made as
shown. Mark the four A locations and the 03 INPUT location.
DRILL
HOLES:
Drill 1-1/4″ diameter hole thru trim side only drill 3/8″ diameter holes thru trim side only, 4 places STEP 2: PREP & INSTALL TRIM
|
---|---
Place trim onto the door| Install backplate with four 1/4-20 x 1″ long screws
and lock washers provided with exit device
|
Mark and drill a 3/8″ diameter (1/2″ max) hole thru the door| Mortise lock and
mounting hardware provided with exit device. Fasten screws loosely.
|
Assemble top of pull to trim with the screw provided| Install collar & lock
cylinder
|
Fasten the bottom of the pull with a screw and finish the washer provided|
Tighten screw nearest trim side of door only
RIM INSTALLATION COMPLETE
Continue installation using device instructions
Detex Corporation, 302 Detex Drive, New Braunfels, Texas 78130-3045
830-629-2900 /
800-729-3839 / Fax
800-653-3839 / Text photos only:
830-481-6433 / INTERNET:
www.detex.com
INSTALLATION INSTRUCTIONS FOR MORTISE 03CM TRIM
DWG #: 103295
TOOLS AND SUPPLIES
Safety Glasses
(Always put on safety glasses prior to beginning installation of the unit)
Pencil, Center Punch, Hammer, Drill Motor
Drill Bits & Taps, Screw Driver (Phillips Drive), Tape Measure
Owner’s Copy
|
---|---
For WARRANTY information, scan the code below or
go to www.detex.com/warranty| For device
installation videos, scan the code below or
go to www.detex.com/videos
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>