DETEX 103200 30 Series Mortise Exit Device Instruction Manual
- June 4, 2024
- DETEX
Table of Contents
- DETEX-103200-30-Series-Mortise-Exit-Device-product-image
- Hardware Table for BASIC device mounting.
- 7 or 13/64″
- 7 or 13/64″
- 7 or 13/64″
- 14 x 1″ PPH self-drilling
- 14 x 1-1/4″ PPH wood screw
- 14 Lockwasher
- 12 x 1″ self-drilling
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
DETEX-103200-30-Series-Mortise-Exit-Device-product-image
Should you have a Question/Problem with your Detex device please call Detex Technical Support from the job site at 1-800-729-3839 and choose option 2 on our menu. Please do not return the product to the distributor.
For WARRANTY information, scan code below or
go to www.detex.com/warranty
For device installation videos, scan code below or
go to www.detex.com/vidoes
PARTS BREAKDOWN
Item| Order
Part #
| Description
1KIT| 105500-X| Centercase/Pushpad SubAssembly (includes
1A)
1A| 100698-2| Centercase Assembly, Wide Stile
2KIT| 103806-9| Mounting Plate/Strike Locator Kit, Mortise (includes
2A, 2B & 2C)
2A| 103215| Mounting Plate, BP9
2B| 103284| Template, RHR, Mortise
2C| 103285| Template, LHR, Mortise
3| 102353-1| Centercase Cover, Stainless Steel, Wide, 10 series, 630
104601-1| Centercase Cover, Aluminum, Wide, 10 series, 628
4
| 100147| Endcap bracket for EC1 (ramped) endcap w/o battery holder
101093| Endcap bracket for EC1 (ramped) endcap w/ battery holder
104303| Endcap bracket for EC2 (flush) endcap w/o battery holder
104636| Endcap bracket for EC2 (flush) endcap w/ battery holder
5
| 101642-9| Endcap, EC1 (ramped) Stainless Steel, 630
104304-9| Endcap, EC2 (flush) Stainless Steel, 630
104612-1| Endcap, EC2 (flush) Aluminum, 628
6
| | Fillerplate, Subassembly, S&R, Less Dogging, LD, 10 series, 36″
| Fillerplate, Subassembly, S&R, Hex Dogging, HD, 10 series, 36″
| Fillerplate, Subassembly, S&R, Cylinder Dogging,CD, 10 series, 36″
7| 100450| Hex Key (for Hex Dogging)
8| 100783| Cylinder Nut (for Cylinder Dogging)
9| 102216-2| Hex Dogging Assembly
102216| Cylinder Dogging Assembly
10
| 103285-X| Strike Kit, ANSI (includes
hardware)
103294-X| Strike Kit, ANSI, flat lip (includes
hardware)
103286-X| Strike Kit, Double door, short open back (includes hardware)
103289-X| Strike Kit, Double door, long open back (includes hardware)
11| 103203-X| Front plate
12| 103320-1| Mortise lock, standard
103303-2| Mortise lock, EE
13| 103273| Latchbolt block
Hardware Table for BASIC device mounting.
Additional hardware is provided per the device configuration
| Fastener Part No| Drill Bit
---|---|---
|
P/N: 100980 1/4-20 x 1″ PPH
|
7 or 13/64″
|
P/N: 100954
1/4-20 x 1-1/2″ PPH
|
7 or 13/64″
|
P/N: 101621-5
1/4-20 x 1/4″ PPHMS
|
7 or 13/64″
| P/N: 101632-2
10-32 x 5/16″ PFHUMS
(multiple finishes included)
|
———-
| P/N: 100162-106
6-32 x 3/8″ PFHUMS
(multiple finishes included)
| ———-
|
P/N: 103276-63
14 x 1″ PPH self-drilling
|
1/8 pilot hole recommended for self-drilling screws
| P/N: PP-5183-110
14 x 1-1/4″ PPH wood screw
|
1/8 pilot hole recommended for wood screws
|
P/N: PP-5067-25
14 Lockwasher
|
|
P/N: 100156-108 #8-32 x 1/2 “
|
———-
|
P/N: PP-5802-118 12-24 x 1/2″
|
———-
|
P/N: 103253-52
12 x 1″ self-drilling
|
———-
Tools Required:
- Safety Glasses pencil
- Power Drill hammer
- Tape Measure pliers
- Level 1/4- 20 Tap
Phillips & small flat Screw Drivers
Combination Square
Center Punch
Saw for cutting device if necessary (chopsaw preferred)
STEP 1: DOOR PREP (Note: LHR installation shown)
Use plastic template to mark and drill mortise lock and backplate holes
NOTES:
- File sharp corners to complete slots where needed.
- See Trim instructions where applicable for drilling trim holes.
- See electrical instructions for wiring electrical devices.
INSTALL MORTISE LOCK
INSTALL BACKPLATE
INSTALL DEVICE
Minimum Filler plate Length
Type| Length (L)
LD| 2-1/2″
HD/CD| 3″For aluminum Advantix finish cutdown applications: After cutting, the baseplate extrusion can be reversed to place the cut end inside the head cover. To do so, loosen the setscrew inside the aluminum baseplate extrusion and slide extrusion out, reverse, & slide back in. Tighten setscrew.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>