ieGeek ZS-GX3S Wire-Free Battery Camera User Manual

ieGeek ZS-GX3S Wire-Free Battery Camera

Camera Introduction

1. Lens
2. Spotlight
3. Working Status Indicator
4. Charging Indicator
5. PIR
6. Microphone
7. Reset
8. SD Cord Slot
9. Power Button
10. USB Port
11. Bracket Mount Port

to the factory setting
SD Card Slat| Support local SD card storage (up to 1280)
---|---

Charging Indicator

|

Red means charging, blue means fully charged

Working Status Indicator

| Solid on red: Network is abnormal
Slow flickering red : Awaiting Wi-Fi connection and start adding devices
Wi-Fi fast flickering red: Wi-Fi connecting
Solid on blue : Wi-Fi connected successfully, the camera running normally

APP Download and Account Registration

Download ‘ieGeek Cam’ APP

• Method 1: Download the ‘ieGeek Cam’ or ‘CloudEdge’ APP from APP Store (iOS and Android);
• Method 2: Scan ‘ieGeek Cam’ APP QR code to download it.

Tips:
Please turn on the 2 below permissions while using this APP for the first time.

• Allow the ‘ieGeek Cam’ APP to access mobile cellular data and wireless LAN or it will fail to add an IP camera.
• Allow the ‘ieGeek Cam’ APP to receive pushed messages or the phone will not receive alarm push when motion detection or audible alarm is triggered.

Register Account

New users need to register by email. The concrete steps are as follows:

1. Click “Register”;
2. Follow the steps to complete the registration of the account;
3. Log in.

Note:

• When registering a new account, please choose the region in which you are actually and the correct country code. (Different registered regions can’t share the camera.)
• Please choose to register by e-mail. Please choose to register by e-mail.

How to Add a Camera to the APP

Before Using

1. Please insert the Micro SD card before powering it on, otherwise, the SD card cannot be detected.
2. Put the camera and smartphone l-3 ft (30-100 cm) away from the router to set Wi-Fi.
3. Make sure that the camera is using 2.4GHz Wi­Fi.

Wi-Fi Connection Steps

Note: If it can’t be powered on, please plug in the DC 5V 2A power adapter to charge the camera for 15min first.

Does my camera fail to connect to Wi-Fi?

1. Please make sure the Wi-Fi the camera is connected to is 2.4GHz.
2. Make sure the password correction of the Wi-Fi is. (Note: the password of the WiFi cannot include a single quote, underline, space, and virgule (/).
3. Once the devices that your router connected exceed its max limit numbers, other devices will not connect to the router.
4. Make sure the QR code on the phone screen is normal and the distance between the phone and the camera lens is l0-l5cm (3.9-5.9inch) during the scanning process.
5. If the camera cannot connect to the Wi-Fi, please try to re-download the APP, reset the camera and restart the router, and then add the camera again.
6. If you tried all steps, but still had no luck, please message your order and problem to www.service@iegeekcom.

Charge the Battery

Charge the battery with a 5V 2A power adapter

• The battery is a built-in battery and cannot be removed.

Charge the battery with the ieGeek Solar Panel. For weatherproof performance, always cover the USB charging port with the rubber plug after finishing charging the battery.

Charging Indicator:

• Red LED: Charging
• Blue LED: Fully Charged

Installation Guides

• Use the camera skin for better weatherproof performance when you install the camera outdoors.
• Install the camera 2-3 meters (7-10 ft) above the ground. The detection range of the motion sensor would be maximized at such a height.
• Install the camera 2-3 meters(7-l0 ft) above ground. The detection range of the motion sensor would be maximized at such a height.
• For effective motion detection, please install the camera angularly.

NOTE:
If a moving object approaches the PIR sensor vertically, the camera may fail to detect motion.

Notes on PIR Motion Sensor

PIR Sensor Detection Range
The PIR detection range can be customized to meet your specific needs. You may refer to the following table to set it up in Device Settings via ieGeek Cam App.

• Sensitivity: Detection Distance (For moving and living objects)
• Level l-3 (Low): Up to 2-5 meters
• Level 4-7 (Med): Up to 5-8 meters
• Level 8-10 (High): Up to 8-10 meters

Important Notes on Reducing False Alarms

• Do not face the camera toward any objects with bright lights, including sunshine, bright lamp lights, etc.
• Do not place the camera near any outlets, including the air conditioner vents, humidifier outlets, the heat transfer vents of projectors, etc.
• Do not install the camera in places with strong wind.
• Do not face the camera toward a mirror.
• Keep the camera at least l meter away from any wireless devices, including WiFi routers and phones in order to avoid wireless interference.

FAQs

For more detailed FAQs, please log in to the APP, search in “Me”-“EAQ”-“Help Document”-“Battery Camera

The device prompts offline.

1. Check whether the equipment is in the power­on state, and observe whether the working light of the equipment is on normally;
2. Confirm that the current location has good wifi coverage and the network is stable, make sure that the wifi signal is above 75%;
3. You can try to use the third-party wifi analysis tool “wifi analyzer” to analyze the current wifi signal coverage and interference status. If the coverage is poor and the interference is large, it is recommended to replace the camera installation position or adjust the router position or use a second-stage router;
4. Avoid using wifi extenders.

Update router or Wi-Fi password?
Delete the camera from your CloudEdge account. After resetting the device, use the new Wi-Fi and password to add it again.

Will not connect to WiFi?

1. The wifi currently connected to the mobile phone is a 2.4Ghz network; The current location has good wifi coverage and a stable network (wifi signal is greater than 75%);
2. Avoid using wifi extender;
3. Check whether the wifi password is entered correctly;

It cannot be ruled out that in the rare case of special network incompatibility, the App and the camera cannot be connected correctly. In this case, our camera is not compatible, please contact the after-sales service first. (service@iegeek.com).

Fast power consumption?

1. In the case of poor wifi coverage (such as signal is below 75%), which will increase power consumption;
2. The PIR trigger frequency is high, and the power consumption will increase when infrared light/ white light is on at night;
3. The mobile phone often accesses the camera remotely, which will increase power consumption;
4. For the first use, it’s recommended to use the power to 10%, and then charge it to 100%, which is helpful for the health of the lithium battery.

camera not detecting movement?

1. In the case of an unstable network, the message may not be pushed in time after the PIR is triggered. In this case, you can first confirm the network status and remove the camera to verify and confirm in an environment with good network coverage;
2. An inappropriate installation position will result in PIR not triggering and not detecting. If the position is too high, the object is too far away, or the object is too small, the camera will not trigger, try to adjust the installation position according to the trigger requirements many times.

SD card not recognized?

1. Support capacity is 16-128GB micro SD card;
2. Before use, make sure to format the micro SD card as FAT32 or exFAT file system on the computer, then insert it into the camera, and finally perform the format memory card operation on the camera again;
3. If the micro SD card is not recognized during use, it is generally a quality problem of the micro SD card, and it is necessary to replace the memory card with more stable reading and writing.

www.iegeek.com

ieGeek and ieGeek logo are trademarks of Shenzhen Globalebuy Co, Ltd, registered in the United States and other countries. All right reserved.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>