LNC A04344 Miguel Distressed Weathered Wood Linear Chandelier Instruction Manual

: June 9, 2024
: LNC

Table of Contents

LNC A04344 Miguel Distressed Weathered Wood Linear Chandelier
Instruction
IMAGE FOR FINISHED PRODUCT
TOOLS REQUIRED
ASSEMBLY & INSTALLATION INSTRUCTIONS
CLEANING
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

LNC A04344 Miguel Distressed Weathered Wood Linear Chandelier

LNC-A04344-Miguel-Distressed-Weathered-Wood-Linear-Chandelier-
product

Instruction

WARNING (To reduce the risk of fire, electric shock, or personal injury):

We suggest installation by a licensed electrician.
Please read the instruction carefully and save it as you may need it at a later time.
Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
- Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
- Place the wall switch in the “OFF” position.
Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
Make sure that the ceiling or wall can stand the weight of the lamp before installation.
Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.
Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

LNC-A04344-Miguel-Distressed-Weathered-Wood-Linear-Chandelier-
fig1

TOOLS REQUIRED

(NOT INCLUDED)

Before starting assembly and installation please prepare the needed tools as below picture

PARTS TYPE & QTY INCLUDING:

(C) Mounting plate assembly (1)
(F) Canopy (1)
(G) Loop (4)
(H) Quick link (4)
(I) Ball knob (2)
(J) Chain (2)
(K) Tube (2)
(L) Adapter (2)
(M) Nut (8)
(N) Upper frame (1)
(O) Side frame (2)
(P) Batten (4)
(Q) Front frame (2)
(R) Stem (2)
(S) Sockets assembly (2)
(T) The lower frame (1)
ACCESSORIES & QTY ENCLOSED:
(A) Wire connector (3)
(B) Anchor (4)
(D) Mounting screw (2)
(E) Wood screw (4)

ASSEMBLY & INSTALLATION INSTRUCTIONS

Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
Make preinstallation
- Step A1 » Carefully pass the fixture wires through flat spacers, upper frame (N), adapters (L) and tubes (K), then screw adapters (L) and tubes (K) onto stems (R). Adjust the angle of sockets assemblies (S).
- Step A2 » Insert battens (P), front frames (Q) and side frames (O) into lower frame (T), then secure them with nuts (M).
- Step A3 » Insert battens (P), front frames (Q) and side frames (O) into upper frame (N), then secure them with nuts (M).
- Step B1 » By measuring, determine the correct number of links needed for proper hanging height. Using the chain pliers, disconnect and discard the unwanted part.
- Step B2 » Attach quick links (H) to chains (J) and loops (G) on canopy (F) and the top of stems (K)
- Step B3 » Carefully weave the fixture wires through chains (J) in and out of every other link and stop just when you reach the top of chains (J). Gently pull the wires to ensure the wires are not stressed.
Turn off power
Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
- Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
- Place the wall switch in the “OFF” position.
Make installation
- Step B1 » Unscrew ball knobs (I) and carefully remove mounting plate assembly (C).
- Step B2 » Carefully pass the supply wires from the outlet box through mounting plate (C).
  NOTE: To drill the holes on the wall for anchors (B):
- Attach mounting plate (C) to the outlet box with mounting screws (D) and mark the holes.
- Unscrew mounting screws (D) and remove mounting plate (C).
- Drill holes and gently knock anchors (B) into the holes until anchors (B) are level with the wall.
  Secure mounting plate (C) to the outlet box with mounting screws (D) and wood screws (E).
- Step B3 » If needed, shorten the length of fixture wires. At this point, the remaining wire length measured above mounting plate assembly (C) is at least 6″.
- Step B4 » Make wire connections
  Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
  Connect ground wires according to the below chart
  Connect wires according to the below chart
  Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
- Step B5 » Raise canopy (F) to the ceiling and secure canopy (F) in place by tightening ball knobs (I) onto the preassembled mounting screws on mounting plate assembly (C).
  NOTE: canopy (F) should be snug against the ceiling with ball knobs (I). If not, remove canopy (F), adjust the threaded length of preassembled mounting screws on mounting plate assembly (C):
- First, unscrew the preassembled hex nuts.
- Then, screw the preassembled mounting screws in or out of mounting plate (C).
- When the secure length is achieved, tighten the preassembled hex nuts and back to Step B5.
- Step B6 » Install bulbs (not included) (Please do not exceed the maximum wattage recommended on the socket.)
Check everything is already installed properly, then you could turn on the light. Enjoy!

ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustrations when ordering parts.