HOLLYLAND B0BWJ9Y71G Solidcom C1 Pro Wireless Intercom Remote Headset User Manual
- June 12, 2024
- HOLLYLAND
Table of Contents
Solidcom C1 Pro Wireless Stereo Headset
User Manual
V2.0.0
Product Interfaces
Operation Guide
Microphone Boom Indicator Description 
-
Indicator light flashes: Unconnected (for remote headsets) *
-
Indicator light flashes quickly: Pairing (The indicator light color is subject to the current state during pairing.)
-
Indicator light stays ON: Master headset turned ON/Remote headset connected successfully
A. Steady green light: ENC OFF
B. Steady blue light: ENC ON
C. Steady red light: MUTE -
Red indicator light flashes twice: Low battery
Sound Description
“Low battery”: The device battery is low.
- The indicator light flashes when a remote headset is not connected, and it stays ON by default when the master headset is turned ON.
Button/Switch Description
-
TALK/MUTE Button
1. Press the button to switch to the TALK mode, and press the button again to switch to the MUTE mode. In this case, the indicator light turns red.
2. Press and hold the button to switch to the TALK mode (PTT function), and then release the button to switch to the MUTE mode. -
ENC Switch
1. When the
switch is pushed to the ENC position, yellow is displayed and ENC is enabled.
2. When the switch is pushed away from the ENC position, black is displayed and ENC is disabled.
Parameters
| Transmission Range | 1,100ft (350m) LOS |
|---|---|
| Frequency Band | 1.9 GHz (DECT) (varies by country and region) |
| Modulation Mode | GFSK |
| i X Power | s21dBm (125.9 mW) |
| RX Sensitivity | <-90dBm |
| Battery Capacity | 700mAh (2.66Wh) |
| Charging Time | About 2.5 hours |
| Frequency Response | ENC OFF: 150Hz-7kHz (fluctuation range: ±6dB) ENC ON: |
150Hz-7kHz (fluctuation range: ±6dB)
Signal-to-Noise Ratio| 71-±2dB@94dBSPL, 1kHz
Distortion| <1%@94dBSPL, 150Hz-7kHz
Microphone Type| Electret
Input SPL| >115dBSPL
Output SPL| 94±3dBSPL (@94dBSPL, 1 kHz)
ENC| 20dB-±2 with two microphones
(relative to environmental noise in all directions)
Net Weight| About 170g (6oz) with batteries included
Temperature Range| 0°C to 45°C (working condition)
-10°C to 60°C (storage condition)
Note: The frequency band and TX power vary by country and region.
Safety Precautions
Do not place the product near or inside heating devices (including but not
limited to microwave ovens, induction cookers, electric ovens, electric
heaters, pressure cookers, water heaters, and gas stoves) to prevent the
battery from overheating and exploding.
Do not use non-original charging cases, cables, and batteries with the
product.
The use of non-original spare parts may cause electric shock, fire, explosion,
or other dangers.
Support
If you encounter any problems in using the product or need any help, please contact Hollyland Support Team via the following ways:
Hollyland User Group
HollylandTech
HollylandTech
HollylandTech
support@hollyland-tech.com
www.hollyland-tech.com
Statement
All copyrights belong to Shenzhen Hollyland Technology Co., Ltd.
Trademark Statement
Without the written approval of Shenzhen Hollyland Technology Co., Ltd., no
organization or individual may copy or reproduce part or all of any written or
illustrative content and disseminate it in any form.
Note:
Due to product version upgrades or other reasons, this User Manual will be
updated from time to time. Unless otherwise agreed, this document is provided
as a guide for use only. All representations, information, and recommendations
in this document do not constitute warranties of any kind, express, or
implied.
FCC Requirement
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the device. This
device complies with Part 15 of the FCC Rules.
Operations are subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operations.
FCC Radiation Exposure Statement:
The device has been tested and complies with FCC SAR limits.
Note:
This device has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This device generates, uses, and can radiate radio
frequency energy, and if it is not installed and used in accordance with the
instructions, it may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this device does cause harmful intefrference to
radio or television reception, which can be determined by turning the device
off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the distance between the device and the receiver.
- Connect the device to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>