LIGIANT G2 Electronic Toy Beach Car Owner’s Manual

LIGIANT G2 Electronic Toy Beach Car

• WARNING Must be assembled by an adult.
• Read and understand this entire manual before using it
• Charge the battery for at least 4-6 hours before the first use.
• Please keep this manual for future reference as it contains important information.

About Your New Vehicle

• On the purchase of your new Ride-On.
• To ensure a safe ride for your child, please read this manual carefully and keep it for future reference. This ride-on car will provide your child with many miles of enjoyable riding.
• To improve the safety and operation of your ride-on car and its rider, please follow the recommendations in this manual.

Specification

Depending on the local voltage
Motor| 390-9000- 12000
Suitable age:| 3+ Years
Charge time:| 8-12 hours
Load capacity:| Max. 66 lbs
Size of car:| 720400455 mm
Speed:| 2.8-4.6 km/h

Parts List

Parts Diagram

Safety

AVOID INJURIES AND DEATHS:

• NEVER LEAVE CHILD UNATTENDED. ADULT DIRECT SUPERVISION IS REQUIRED ALL TIME.
• Keep the child in view at all times when they are in the vehicle.
• This toy should be used with caution, as skill is required to avoid falls or collisions that could cause injury to the user or third parties.
• Wear protective equipment.
• Never use it on roadways, near cars, on steep inclines or steps, in swimming pools, or in other bodies of water.
• Always wear shoes and sit on the seat.
• Do not use it in traffic.
• This toy is not suitable for children under 36 months due to its maximum speed, and the maximum user weight is 66 lbs.
• This toy does not have a brake.

WARNING

• CHOKING HAZARD! Not suitable for children under 36 months.
• Assembly must be done by an adult.
• To minimize the risk of injury, adult supervision is essential.
• Never use it on roadways, near motor vehicles, on or near steep inclines or steps, swimming pools, or other bodies of water; always wear protective footwear, and never allow more than one rider at a time.
• The power supply or battery charger used with the electric toy should be inspected regularly for any damage to the supply cord, plug, enclosure, or other parts. If any damage is found, it should not be used until it has been repaired.
• The battery on the vehicle cannot be replaced.

Rules for Safe Riding

• Keep Children Within Safe Riding Areas.
• Use the toy only on flat surfaces, such as inside your house, garden, or playground. Never use the vehicle in the dark, as a child could encounter unexpected obstacles and have an accident.
• Operate the vehicle only in the daytime or in a well-lit area. Never change the circuit or add other electric parts.
• Inspect wires and connections of the vehicle periodically.
• Keep children away from the wheels when the car is moving.

Install the Front Axle Linkage

Carefully flip the vehicle body over.

1. Attach the front axle linkage to the vehicle body.
2. Insert four 4* 16 screws through the front axle linkage and into the vehicle body, and tighten the securely with a screwdriver.

Turn the vehicle onto its side

1. Insert the straight end of the steering column into the hole on the vehicle body and out through the hole on the top of the vehicle body, ensuring a secure fit.
2. Insert the bent end of the steering column into the hole on the front axle linkage, ensuring that it is securely fastened.

Attach the Handlebar

Flip the vehicle body over

1. Insert the power unit connector into the hole in the vehicle body.
2. Attach the handlebar to the end of the steering column.
3. Line up the holes on the steering wheel with the holes on the steering column, and insert the M5x30 machine screw.
4. Fasten a nut on the opposite end of the screw, using long nose pliers to hold the nut in place while tightening the screw with a screwdriver.
5. Insert the power unit connector into the connector on the vehicle body.

Attach the Rear Wheels

1. Slide a wheel onto the rear axle from the right side, making sure it is properly aligned with the gearbox.
2. Slide a 10-washer onto the rear axle.
3. Tighten a lock nut to the end of the rear axle using a spanner.
4. Insert the tabs on the wheel cover (or hubcap) into the grooves on the wheel to secure it in place.
5. Slide a 10-washer onto the rear axle from the left-hand side.
6. Slide a wheel onto the rear axle.
7. Slide a 10-washer onto the rear axle.
8. Tighten a lock nut to the end of the rear axle using a spanner.
9. Insert the tabs on the wheel cover (or hubcap) into the corresponding grooves on the wheel.

Attach the Front Wheels

1. Slide a 10-washer onto the left side of the front axle.
2. Slide a wheel onto the front axle.
3. Slide a10 10-washer onto the front axle
4. Tighten a lock nut to the end of the front axle using a spanner.
5. Insert the tabs on the wheel cover (or hubcap) into the corresponding grooves on the wheel.

External charging type Connecting the Power Supply

If your product is an External Charging type, follow the instructions on this page.

1. Using a slotted screwdriver (not included) or a coin, turn the seat lock and remove the seat.
2. Plug the vehicle connector into the connector from the battery.
3. Reinstall the seat.

Use your new ride-on

IMPORTANT!

• Always stop the vehicle when changing the speed or direction to avoid damaging the gears and motor.

1. Power button:

   • To move the vehicle, press the button.
   • To stop the vehicle or slow down, release the button.

2. Forward/stop/reverse

   • Change the direction of the switch: the product’s movement from forward to reverse.
   • To move the product forward, press the switch to the topper position.
     To move the vehicle reverse, press the switch to the downward position

3. (If equipped) Music/horn button Press for music/horn playing.

Charging

WARNING

• An adult is the only one who can charge and recharge the battery.

WARNING

• This product has Charging Protection: when charging, all functions will be disabled!
• When the vehicle runs slowly, recharge the battery to optimize performance.
• Before the first use, charge the battery for 4-6 hours. Do not recharge for more than 10 hours to avoid overheating.
• Charge the vehicle after each use or at least once a month for 8 to 12 hours, but no more than 20 hours per charge.
• Use ONLY the rechargeable battery and charger supplied with your vehicle. DO
• NOT substitute with another brand, as this may cause a fire or explosion.
• Do not use the battery or charger for any purpose other than its intended use.

External charging type

1. Plug the charger port into the input socket on the back of the vehicle body.
2. Plug the charger into a wall outlet and the battery will begin charging.

Battery charing type

• A. Use a slotted screwdriver(not included) or coin to turn the seat lock counterclockwise to the end, and remove the seat.
• B. Unpulg the battery connector with the vehicle connector.
• C. Plug the charger connector into the battery connector.
• D. Plug the charger plug into a wall outlet. The battery will begin charging.

Install the Front Axle Linkage

connectors are firmly plugged in. If wires are loose around the motor, please contact your distributor.
Dead Battery| Replace the battery, please contact your distributor.
Electrical system damaged| Please contact your distributor.
Motor is damaged| Please contact your distributor.

The vehicle does not run very long

| The battery is undercharged| Ensure that the battery connectors are securely connected when recharging.
Battery is old| Replace the battery, please contact your distributor.

Vehicle runs sluggishly

| Low battery| Replace the battery, please contact your distributor.
Battery is old| Replace the battery, please contact your distributor.
Vehicle is overload| Reduce vehicle load.
The vehicle is being used in harsh conditions| Avoid using vehicles in harsh conditions, see .
The vehicle needs to be pushed forward.| Poor contact with wires or connectors| Check that the battery connectors are firmly plugged into each other, please. If wires are loose around the motor, please contact your distributor.
“Dead spot” on wiring| The vehicle needs repair as there is a dead spot, meaning the electric power is not being delivered to the terminal connection Please contact your distributor.
Difficult to shift from forward to reverse or vice-versa| Attempting to shift while the vehicle is in motion| Completely stop the vehicle and shift, see