Superlightingled LN-40-12 0/1-10V Constant Voltage LED Driver Instruction Manual

June 9, 2024
SuperLightingLED

LN-40-12 0/1-10V Constant Voltage LED Driver
Instruction Manual

Superlightingled LN-40-12 0 1-10V Constant Voltage LED
Driver

Features

  • Dimming interface: 0-10V, 1-10V, 10V PWM, Resistor, AC Push-Dim
  • Universal AC input / Full range
  • 1 channel constant voltage output, Max. total output power 40W
  • Synchronize on multiple number of LED drivers
  • Over-heat / Over-load / Short circuit protection, recover automatically
  • Full protective plastic case
  • Suitable for indoor LED lighting application
  • 5 Year, 50,000hr warranty

Mechanical Structures and Installations

Superlightingled LN-40-12 0 1-10V Constant Voltage LED Driver - Figure
1

Technical Parameters

Model LN-40-1 2 LN-40-24
Output Output Voltage 12VDC
Output Current Max. 3.34A Max. 1.67A
Output Power Max. 40W
Dimming Range 0-100%
Ripple & Noise <=200mV/230VAC <=280mV/230VAC
PWM Frequency 500Hz
Input Input Voltage Range 100-240VAC
Frequency Range 50/60Hz
Efficiency 81 %/230VAC 86%/230VAC
Alternating Current 0.70A/115VAC, 0.41A/230VAC 0.67A/1 15VAC, 0.40A/230VAC
Inrush Current Cold start 27.5A at 230VAC
Leakage Current <5mA
No Load Power 0.8W/115VAC, 1.2W/230VAC I 1.6W/1 15VAC, 2.1W/230VAC
Protection Over Load Power Shut down the output when current load >=

120%-150%, auto recovers.
Short Circuit| Shut down automatically if short circuit occurs, auto recovers
Over Temperature| Intelligently adjust or turn off the output current if the PCB temp > 100°C, auto recovers
Environment| Woking Temperature| -30°C-50°C
Tcase Max| 70t
Working Humidity| 20%-90%RH, non-condensing
Storage Temperature/Humidity| -40°C-80°C, 10%-95 %RH
Temperature Coefficient| ±0.03%/t l0-50%)
Vibration Resistance| 10-500Hz, 2G, 6min/cycle, X,Y,Z axes/2min
IP Rating| IP20
Safety&EMC| Security Specifications| IEC/EN61347-1, IEC/EN61347-2-13
Withstand Voltage| I/P-0/P: 3750VAC
Insulation Resistance| I/P-0/P: 100M0/500VDC/25°C/70%RH
EMC Emission| EN55015, EN61000-3-2 Class C, IEC61000-3-3
EMC Immunity| EN61000-4-2.3.4.5.6.8.11, EN61547
Certications| CE, EMC

Applications

  • Suitable for LED related fixture or appliance which use LED light bar and LED tape (like LED Decoration or Advertisement devices).
  • Office / Commercial / Domestic Lighting, Hotels, Retail and Display.
  • Use for retrofit upgrades & new luminaire designs.

Wiring Diagram

  1. 0/1-10V Connection
    Superlightingled LN-40-12 0 1-10V Constant Voltage LED Driver - Figure
3● The 0/1-10V input is operable via commercially available simple rotary wall switchs designed for 0/1-10V dimming equipment or from decicated system central  dimming controllers.
    ● Compliant with 0-10V, 1-10V, 10V PWM, RX(4 in 1).
    ● We recommend the number of LED drivers connected to 0/1-10V dimmer does not exceed 5 pieces,
    The maximum length of the wires from dimmer to LED driver should be no more than 15 meters.
    ● If the LED driver be used with the RF remote or Push-Dim interface prior to using the 0/1-10V interface, the 0/1-10 V signal should change over 10% to return 0/1- 10 V control.

  2. AC Push-Dim connection
    Superlightingled LN-40-12 0 1-10V Constant Voltage LED Driver - Figure
2

The provided AC Push-Dim interface allows for a simple dimming method using commercially available non-latching (momentary) wall switchs.

  • Short press:
    Turn on or off light.

  • Long press (1-6s):
    Press and hold to step-less dimming,
    With every other long press, the light level goes to the opposite direction.

  • Dimming memory:
    Light returns to the previous dimming level when switched off and on again, even at power failure.

  • Synchronization:
    If more than one LED driver are connected to the same push switch, do a long press for more than 10s, then the system is synchronized and all lights in the group dim  up to 100%.
    This means there is no need for any additional synchrony wire in larger installations.
    We recommend the number of LED drivers connected to a push switch does not exceed 25 pieces, The maximum length of the wires from push to LED driver should  be no more than 20 meters.

Dimming Curve

Superlightingled LN-40-12 0 1-10V Constant Voltage LED Driver - Figure
4

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

SuperLightingLED User Manuals

Related Manuals