RAB Lighting HIDFA-XXS-H-E26-8CCT-BYP Wall Pack Series Instructions
- June 8, 2024
- RAB Lighting
Table of Contents
HIDFA-XXS-H-E26-8CCT-BYP
HIDFA-XXS-H-EX39-8CCT-BYP
Lighting Wall Pack Series
Instructions
HIDFA-XXS-H-E26-8CCT-BYP Wall Pack Series
RAB Lighting is committed to creating high-quality, affordable, well-designed
and energy-efficient LED lighting and controls that make it easy for
electricians to install and end users to save energy. We’d love to hear your
comments. Please call the Marketing Department at 888-RAB-1000 or email:
[email protected]
IMPORTANT
READ CAREFULLY BEFORE INSTALLING LED HID BULBS. RETAIN THESE INSTRUCTIONS FOR
FUTURE REFERENCE.
RAB LED HID Bulbs must be wired in accordance with the National Electrical
Code and all applicable codes. Proper grounding is required for safety. THIS
PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE
BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND
THE HAZARDS INVOLVED.
WARNINGS:
- Main applications include for use in wall pack, cobra head lights, flood lights and other suitable light fixtures.
- Operating temperature:-30°C to 60C(-22F to 140°F).
- These LED Lamps require all ballasts, capacitors, and ignitors to be bypassed or removed. Do not operate lamps on existing ballasts.
- Do not use with standard dimmers.
- This device is not intended for use with emergency exits.
- For use in enclosed fixtures.
- Before installation make certain the AC power to the fixture is off.
- Risk of fire or electric shock. Luminaire wiring and electrical parts may be damaged when drilling for installation of LED retrofit kit. Check for enclosed wiring and components.
- Risk of fire or electric shock. LED Retrofit lamp installation requires knowledge of luminaires electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.
- Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
- Installers should not disconnect existing wires from lampholderterminals to make new connections at lampholder terminals. Instead installers should cut existing lampholder leads away from the lampholder and make new electrical connections to lamp holder lead wires by employing applicable connectors.
- To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
- Risk of fire or electric shock. Install this kit only in luminaires that have the construction features and dimensions shown in the photographs or drawings and where the input rating of the retrofit kit does not exceed the input rating of the luminaire.
- Use only with a portable luminaire that is provided with a shade.
- Added weight of the device may cause instability of a free-standing portable luminaire.
- Please examine all parts that are not intended to be replaced by the retrofit kit for damage and replace any damaged parts prior to installation of the retrofit kit.
- RISK OF FIRE OR ELECTRIC SHOCK. INSTALLATION OFTHIS RETROFIT KIT REQUIRES A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE LUMINAIRE’S ELECTRICAL SYSTEM AND THE HAZARD INVOLVED. IF NOT QUALIFIED, DO NOT ATTEMPT INSTALLATION. CONTACT A QUALIFIED ELECTRICIAN.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
LAMP INSTALLATION
-
Turn off the power before installation.
Remove old ballast or disconnect from existing lampholder. Remove and dispose of ballast in correct manner. Shown as Figure 1. (North America 100-277VAC) -
Reconnect directly to the existing lampholder. Shown as Figure 2.
(North America 100-277VAC)
-
Select power and CCT of new LED replacement lamp before installation.
-
Install new LED replacement lamp. Shown as Figure 3. Please make sure the old fitting is correctly earth. Attach retrofit label to luminaire. (North America 100-277VAC)
Securely fasten the earth fly lead cable to the main body structure. If the
cable are damaged in any way please replace.
(Do not use existing burnt out cables) The cable if need replacement must be
1.0mm in size and insulated from heat.
SELE (TAB IL ITV Power and CCT Selectable
Note: These instructions
do not cover all details or variations in equipment nor do they provide for
every possible situation during installation, operation or maintenance.
| Model Number | Power Selectable | CCT Selectable |
|---|
HIDFA-20S-H-E26-8CCT-BYP
HIDFA-20S-H-EX39-8CCT-BYP| SW| 3000K
10W| 4000K
20W| S000K
HIDFA-30S-H-E26-8CCT-BYP
HIDFA-30S-H-EX39-8CCT-BYP| 10W| 3000K
20W| 4000K
30W| S000K
HIDFA-40S-H-E26-8CCT-BYP
HIDFA-40S-H-EX39-8CCT-BYP| 20W| 3000K
30W| 4000K
40W| S000K
HIDFA-60S-H-EX39-8CCT-BYP| 20W| 3000K
40W| 4000K
60W| S000K
HORIZONTAL LAMP SUPPORT INSTALLATION
Only for 30W 40W 60W lamps
For face-down
installation use the two-legged support and cut to desired length (Fig.4)
For face-out installation use
the one-legged support and cut to desired length (Fig.5)
Easy Answers
rablighting.com
Visit our website for product info
Tech Help Line
Call our experts: 888 722-1000
e-mail
Answered promptly – [email protected]
Free Lighting Layouts
Answered online or by request
RAB WARRANTY: RAB’s warranty is subject to ail terms and conditions found
at rablighting.com/warranty.
© 2021 RAB LIGHTING Inc.
Northvale, New Jersey 07647 USA
HIDFAWP-IN-0821
Documents / Resources
| RAB
Lighting HIDFA-XXS-H-E26-8CCT-BYP Wall Pack
Series
[pdf] Instructions
HIDFA-XXS-H-E26-8CCT-BYP Wall Pack Series, HIDFA-XXS-H-E26-8CCT-BYP, Wall Pack
Series, Pack Series
---|---